diff --git a/kalama-sg-hhg-camera-sensor.dtsi b/kalama-sg-hhg-camera-sensor.dtsi
index 805d29dc..9d9a0d98 100644
--- a/kalama-sg-hhg-camera-sensor.dtsi
+++ b/kalama-sg-hhg-camera-sensor.dtsi
@@ -1,6 +1,13 @@
 #include <dt-bindings/msm-camera.h>
 
 &soc {
+	led_front: qcom,camera-flash1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		switch-source = <&pm8550_led_camera>;
+		status = "ok";
+	};
+
 	qcom,cam-res-mgr {
 		compatible = "qcom,cam-res-mgr";
 		status = "ok";
@@ -8,6 +15,40 @@
 };
 
 &cam_cci0 {
+	eeprom_rear: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000>;
+		rgltr-max-voltage = <1800000 1200000 0 2800000>;
+		rgltr-load-current = <120000 1200000 0 80000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
 	qcom,cam-sensor0 {
 		cell-index = <2>;
 		compatible = "qcom,cam-sensor";
@@ -15,6 +56,7 @@
 		sensor-position-roll = <90>;
 		sensor-position-pitch = <0>;
 		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_rear>;
 		cam_vio-supply = <&L5N>;
 		cam_vdig-supply = <&L2N>;
 		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
@@ -48,6 +90,40 @@
 };
 
 &cam_cci1 {
+	eeprom_front: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+				"cam_vana";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000>;
+		rgltr-max-voltage = <1800000 1200000 0 2800000>;
+		rgltr-load-current = <120000 1200000 0 80000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				&cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				&cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 104 0>,
+				<&tlmm 120 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
 	qcom,cam-sensor1 {
 		cell-index = <4>;
 		compatible = "qcom,cam-sensor";
@@ -55,6 +131,8 @@
 		sensor-position-roll = <90>;
 		sensor-position-pitch = <0>;
 		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		led-flash-src = <&led_front>;
 		cam_vio-supply = <&L5N>;
 		cam_vdig-supply = <&L1N>;
 		cam_clk-supply = <&cam_cc_titan_top_gdsc>;