mirror of
https://github.com/Evolution-X-Devices/kernel_oneplus_sm8550-devicetrees
synced 2026-02-01 09:49:52 +00:00
dc18d4050d
This change adds trusted touch properties for kalama target. Change-Id: I9b3444f35ebce6bad2e9f809a09222d26e4f5e90
186 lines
3.9 KiB
Plaintext
186 lines
3.9 KiB
Plaintext
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/clock/qcom,gcc-kalama.h>
|
|
|
|
#include "kalama-pmic-overlay.dtsi"
|
|
#include "kalama-thermal-overlay.dtsi"
|
|
|
|
&sdhc_2 {
|
|
status = "ok";
|
|
vdd-supply = <&pm_humu_l9>;
|
|
qcom,vdd-voltage-level = <2950000 2960000>;
|
|
qcom,vdd-current-level = <0 800000>;
|
|
|
|
vdd-io-supply = <&pm_humu_l8>;
|
|
qcom,vdd-io-voltage-level = <1800000 2960000>;
|
|
qcom,vdd-io-current-level = <0 5600>;
|
|
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&sdc2_on>, <&sd_card_det_default>;
|
|
pinctrl-1 = <&sdc2_off>, <&sd_card_det_default>;
|
|
|
|
cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
|
|
|
|
resets = <&gcc GCC_SDCC2_BCR>;
|
|
reset-names = "core_reset";
|
|
|
|
qcom,iommu-dma = "bypass";
|
|
qcom,uses_level_shifter;
|
|
};
|
|
|
|
&soc {
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
label = "gpio-keys";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&key_vol_up_default>;
|
|
|
|
vol_up {
|
|
label = "volume_up";
|
|
gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
|
|
linux,input-type = <1>;
|
|
linux,code = <KEY_VOLUMEUP>;
|
|
gpio-key,wakeup;
|
|
debounce-interval = <15>;
|
|
linux,can-disable;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pm8550b_haptics {
|
|
status = "okay";
|
|
};
|
|
|
|
&ufsphy_mem {
|
|
compatible = "qcom,ufs-phy-qmp-v4-kalama";
|
|
|
|
/* VDDA_UFS_CORE */
|
|
vdda-phy-supply = <&pm_v6d_l1>;
|
|
vdda-phy-max-microamp = <188000>;
|
|
|
|
/* VDDA_UFS_0_1P2 */
|
|
vdda-pll-supply = <&pm_v6e_l3>;
|
|
vdda-pll-max-microamp = <18300>;
|
|
|
|
/* Phy GDSC for VDD_MX, always on */
|
|
vdd-phy-gdsc-supply = <&gcc_ufs_mem_phy_gdsc>;
|
|
|
|
/* Qref power supply, Refer Qref diagram */
|
|
vdda-qref-supply = <&pm_v6e_l1>;
|
|
vdda-qref-max-microamp = <30000>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&ufshc_mem {
|
|
vdd-hba-supply = <&gcc_ufs_phy_gdsc>;
|
|
|
|
vcc-supply = <&pm_humu_l17>;
|
|
vcc-max-microamp = <1300000>;
|
|
|
|
vccq-supply = <&pm_v6g_l1>;
|
|
vccq-max-microamp = <1200000>;
|
|
|
|
/* VDD_PX10 is voted for the ufs_reset_n */
|
|
qcom,vddp-ref-clk-supply = <&pm_v6g_l3>;
|
|
qcom,vddp-ref-clk-max-microamp = <100>;
|
|
|
|
qcom,vccq-parent-supply = <&pm_v6g_s4>;
|
|
qcom,vccq-parent-max-microamp = <210000>;
|
|
|
|
reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
|
|
resets = <&gcc GCC_UFS_PHY_BCR>;
|
|
reset-names = "rst";
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&pm8550_switch0 {
|
|
qcom,led-mask = <9>; /* Channels 1 & 4 */
|
|
qcom,symmetry-en;
|
|
};
|
|
|
|
&pm8550_switch1 {
|
|
qcom,led-mask = <6>; /* Channels 2 & 3 */
|
|
qcom,symmetry-en;
|
|
};
|
|
|
|
&pm8550_switch2 {
|
|
qcom,led-mask = <15>; /* All Channels */
|
|
qcom,symmetry-en;
|
|
};
|
|
|
|
&pm8550_flash {
|
|
status = "ok";
|
|
};
|
|
|
|
|
|
&qupv3_se4_i2c {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
status = "ok";
|
|
qcom,i2c-touch-active = "goodix,gt9916";
|
|
|
|
goodix-berlin@5d {
|
|
compatible = "goodix,gt9916";
|
|
reg = <0x5d>;
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <25 0x2008>;
|
|
goodix,reset-gpio = <&tlmm 24 0x00>;
|
|
goodix,irq-gpio = <&tlmm 25 0x2008>;
|
|
goodix,irq-flags = <2>;
|
|
goodix,panel-max-x = <1080>;
|
|
goodix,panel-max-y = <2400>;
|
|
goodix,panel-max-w = <255>;
|
|
goodix,panel-max-p = <4096>;
|
|
goodix,firmware-name = "goodix_firmware_i2c.bin";
|
|
goodix,config-name = "goodix_cfg_group_i2c.bin";
|
|
goodix,avdd-name = "avdd";
|
|
goodix,iovdd-name = "iovdd";
|
|
invert_xy;
|
|
avdd-supply = <&L14B>;
|
|
iovdd-supply = <&L12B>;
|
|
goodix,touch-type = "primary";
|
|
goodix,qts_en;
|
|
qts,trusted-touch-mode = "vm_mode";
|
|
qts,touch-environment = "pvm";
|
|
qts,trusted-touch-type = "primary";
|
|
qts,trusted-touch-spi-irq = <569>;
|
|
qts,trusted-touch-io-bases = <0xa90000>;
|
|
qts,trusted-touch-io-sizes = <0x1000>;
|
|
qts,trusted-touch-vm-gpio-list = <&tlmm 44 0 &tlmm 45 0 &tlmm 46 0
|
|
&tlmm 47 0 &tlmm 24 0 &tlmm 25 0x2008>;
|
|
};
|
|
};
|
|
|
|
&eusb2_phy0 {
|
|
dummy-supply = <&pm8550b_eusb2_repeater>;
|
|
usb-repeater = <&pm8550b_eusb2_repeater>;
|
|
};
|
|
|
|
&usb0 {
|
|
usb-role-switch;
|
|
port {
|
|
usb_port0: endpoint {
|
|
remote-endpoint = <&usb_port0_connector>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&ucsi {
|
|
connector {
|
|
port {
|
|
usb_port0_connector: endpoint {
|
|
remote-endpoint = <&usb_port0>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&battery_charger {
|
|
qcom,wireless-fw-name = "idt9418.bin";
|
|
qcom,thermal-mitigation = <3000000 1500000 1000000 500000>;
|
|
};
|