dt-bindings: Add devicetree bindings to devicetree project

Add devicetree bindings snapshot to the devicetree project

Change-Id: I20b46d194bd3b107ddcb3e35283e6dafa27adec1

bindings/timer/actions,owl-timer.txt

@@ -0,0 +1,21 @@
+Actions Semi Owl Timer
+
+Required properties:
+- compatible      :  "actions,s500-timer" for S500
+                     "actions,s700-timer" for S700
+                     "actions,s900-timer" for S900
+- reg             :  Offset and length of the register set for the device.
+- interrupts      :  Should contain the interrupts.
+- interrupt-names :  Valid names are: "2hz0", "2hz1",
+                                      "timer0", "timer1", "timer2", "timer3"
+                     See ../resource-names.txt
+
+Example:
+
+		timer@b0168000 {
+			compatible = "actions,s500-timer";
+			reg = <0xb0168000 0x100>;
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+			             <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "timer0", "timer1";
+		};

bindings/timer/allwinner,sun4i-timer.txt

@@ -0,0 +1,19 @@
+Allwinner A1X SoCs Timer Controller
+
+Required properties:
+
+- compatible : should be one of the following:
+              "allwinner,sun4i-a10-timer"
+              "allwinner,suniv-f1c100s-timer"
+- reg : Specifies base physical address and size of the registers.
+- interrupts : The interrupt of the first timer
+- clocks: phandle to the source clock (usually a 24 MHz fixed clock)
+
+Example:
+
+timer {
+	compatible = "allwinner,sun4i-a10-timer";
+	reg = <0x01c20c00 0x400>;
+	interrupts = <22>;
+	clocks = <&osc>;
+};

bindings/timer/allwinner,sun5i-a13-hstimer.txt

@@ -0,0 +1,26 @@
+Allwinner SoCs High Speed Timer Controller
+
+Required properties:
+
+- compatible :	should be "allwinner,sun5i-a13-hstimer" or
+		"allwinner,sun7i-a20-hstimer"
+- reg : Specifies base physical address and size of the registers.
+- interrupts :	The interrupts of these timers (2 for the sun5i IP, 4 for the sun7i
+		one)
+- clocks: phandle to the source clock (usually the AHB clock)
+
+Optional properties:
+- resets: phandle to a reset controller asserting the timer
+
+Example:
+
+timer@1c60000 {
+	compatible = "allwinner,sun7i-a20-hstimer";
+	reg = <0x01c60000 0x1000>;
+	interrupts = <0 51 1>,
+		     <0 52 1>,
+		     <0 53 1>,
+		     <0 54 1>;
+	clocks = <&ahb1_gates 19>;
+	resets = <&ahb1rst 19>;
+};

bindings/timer/altr,timer-1.0.txt

@@ -0,0 +1,18 @@
+Altera Timer
+
+Required properties:
+
+- compatible : should be "altr,timer-1.0"
+- reg : Specifies base physical address and size of the registers.
+- interrupts : Should contain the timer interrupt number
+- clock-frequency : The frequency of the clock that drives the counter, in Hz.
+
+Example:
+
+timer {
+	compatible = "altr,timer-1.0";
+	reg = <0x00400000 0x00000020>;
+	interrupt-parent = <&cpu>;
+	interrupts = <11>;
+	clock-frequency = <125000000>;
+};

bindings/timer/amlogic,meson6-timer.txt

@@ -0,0 +1,22 @@
+Amlogic Meson6 SoCs Timer Controller
+
+Required properties:
+
+- compatible : should be "amlogic,meson6-timer"
+- reg : Specifies base physical address and size of the registers.
+- interrupts : The four interrupts, one for each timer event
+- clocks : phandles to the pclk (system clock) and XTAL clocks
+- clock-names : must contain "pclk" and "xtal"
+
+Example:
+
+timer@c1109940 {
+	compatible = "amlogic,meson6-timer";
+	reg = <0xc1109940 0x14>;
+	interrupts = <GIC_SPI 10 IRQ_TYPE_EDGE_RISING>,
+		     <GIC_SPI 11 IRQ_TYPE_EDGE_RISING>,
+		     <GIC_SPI 6 IRQ_TYPE_EDGE_RISING>,
+		     <GIC_SPI 29 IRQ_TYPE_EDGE_RISING>;
+	clocks = <&xtal>, <&clk81>;
+	clock-names = "xtal", "pclk";
+};

bindings/timer/andestech,atcpit100-timer.txt

@@ -0,0 +1,33 @@
+Andestech ATCPIT100 timer
+------------------------------------------------------------------
+ATCPIT100 is a generic IP block from Andes Technology, embedded in
+Andestech AE3XX platforms and other designs.
+
+This timer is a set of compact multi-function timers, which can be
+used as pulse width modulators (PWM) as well as simple timers.
+
+It supports up to 4 PIT channels. Each PIT channel is a
+multi-function timer and provide the following usage scenarios:
+One 32-bit timer
+Two 16-bit timers
+Four 8-bit timers
+One 16-bit PWM
+One 16-bit timer and one 8-bit PWM
+Two 8-bit timer and one 8-bit PWM
+
+Required properties:
+- compatible	: Should be "andestech,atcpit100"
+- reg		: Address and length of the register set
+- interrupts	: Reference to the timer interrupt
+- clocks 	: a clock to provide the tick rate for "andestech,atcpit100"
+- clock-names 	: should be "PCLK" for the peripheral clock source.
+
+Examples:
+
+timer0: timer@f0400000 {
+	compatible = "andestech,atcpit100";
+	reg = <0xf0400000 0x1000>;
+	interrupts = <2>;
+	clocks = <&apb>;
+	clock-names = "PCLK";
+};

bindings/timer/arm,armv7m-systick.txt

@@ -0,0 +1,26 @@
+* ARMv7M System Timer
+
+ARMv7-M includes a system timer, known as SysTick. Current driver only
+implements the clocksource feature.
+
+Required properties:
+- compatible	  : Should be "arm,armv7m-systick"
+- reg		  : The address range of the timer
+
+Required clocking property, have to be one of:
+- clocks	  : The input clock of the timer
+- clock-frequency : The rate in HZ in input of the ARM SysTick
+
+Examples:
+
+systick: timer@e000e010 {
+	compatible = "arm,armv7m-systick";
+	reg = <0xe000e010 0x10>;
+	clocks = <&clk_systick>;
+};
+
+systick: timer@e000e010 {
+	compatible = "arm,armv7m-systick";
+	reg = <0xe000e010 0x10>;
+	clock-frequency = <90000000>;
+};

bindings/timer/arm,mps2-timer.txt

@@ -0,0 +1,28 @@
+ARM MPS2 timer
+
+The MPS2 platform has simple general-purpose 32 bits timers.
+
+Required properties:
+- compatible	: Should be "arm,mps2-timer"
+- reg		: Address and length of the register set
+- interrupts	: Reference to the timer interrupt
+
+Required clocking property, have to be one of:
+- clocks	  : The input clock of the timer
+- clock-frequency : The rate in HZ in input of the ARM MPS2 timer
+
+Examples:
+
+timer1: mps2-timer@40000000 {
+	compatible = "arm,mps2-timer";
+	reg = <0x40000000 0x1000>;
+	interrupts = <8>;
+	clocks = <&sysclk>;
+};
+
+timer2: mps2-timer@40001000 {
+	compatible = "arm,mps2-timer";
+	reg = <0x40001000 0x1000>;
+	interrupts = <9>;
+	clock-frequency = <25000000>;
+};

bindings/timer/arm,sp804.txt

@@ -0,0 +1,29 @@
+ARM sp804 Dual Timers
+---------------------------------------
+
+Required properties:
+- compatible: Should be "arm,sp804" & "arm,primecell"
+- interrupts: Should contain the list of Dual Timer interrupts. This is the
+	interrupt for timer 1 and timer 2. In the case of a single entry, it is
+	the combined interrupt or if "arm,sp804-has-irq" is present that
+	specifies which timer interrupt is connected.
+- reg: Should contain location and length for dual timer register.
+- clocks: clocks driving the dual timer hardware. This list should be 1 or 3
+	clocks.	With 3 clocks, the order is timer0 clock, timer1 clock,
+	apb_pclk. A single clock can also be specified if the same clock is
+	used for all clock inputs.
+
+Optional properties:
+- arm,sp804-has-irq = <#>: In the case of only 1 timer irq line connected, this
+	specifies if the irq connection is for timer 1 or timer 2. A value of 1
+	or 2 should be used.
+
+Example:
+
+	timer0: timer@fc800000 {
+		compatible = "arm,sp804", "arm,primecell";
+		reg = <0xfc800000 0x1000>;
+		interrupts = <0 0 4>, <0 1 4>;
+		clocks = <&timclk1 &timclk2 &pclk>;
+		clock-names = "timer1", "timer2", "apb_pclk";
+	};

bindings/timer/arm,twd.txt

@@ -0,0 +1,53 @@
+* ARM Timer Watchdog
+
+ARM 11MP, Cortex-A5 and Cortex-A9 are often associated with a per-core
+Timer-Watchdog (aka TWD), which provides both a per-cpu local timer
+and watchdog.
+
+The TWD is usually attached to a GIC to deliver its two per-processor
+interrupts.
+
+** Timer node required properties:
+
+- compatible : Should be one of:
+	"arm,cortex-a9-twd-timer"
+	"arm,cortex-a5-twd-timer"
+	"arm,arm11mp-twd-timer"
+
+- interrupts : One interrupt to each core
+
+- reg : Specify the base address and the size of the TWD timer
+	register window.
+
+Optional
+
+- always-on : a boolean property. If present, the timer is powered through
+  an always-on power domain, therefore it never loses context.
+
+Example:
+
+	twd-timer@2c000600 {
+		compatible = "arm,arm11mp-twd-timer"";
+		reg = <0x2c000600 0x20>;
+		interrupts = <1 13 0xf01>;
+	};
+
+** Watchdog node properties:
+
+- compatible : Should be one of:
+	"arm,cortex-a9-twd-wdt"
+	"arm,cortex-a5-twd-wdt"
+	"arm,arm11mp-twd-wdt"
+
+- interrupts : One interrupt to each core
+
+- reg : Specify the base address and the size of the TWD watchdog
+	register window.
+
+Example:
+
+	twd-watchdog@2c000620 {
+		compatible = "arm,arm11mp-twd-wdt";
+		reg = <0x2c000620 0x20>;
+		interrupts = <1 14 0xf01>;
+	};

bindings/timer/brcm,bcm2835-system-timer.txt

@@ -0,0 +1,22 @@
+BCM2835 System Timer
+
+The System Timer peripheral provides four 32-bit timer channels and a
+single 64-bit free running counter. Each channel has an output compare
+register, which is compared against the 32 least significant bits of the
+free running counter values, and generates an interrupt.
+
+Required properties:
+
+- compatible : should be "brcm,bcm2835-system-timer"
+- reg : Specifies base physical address and size of the registers.
+- interrupts : A list of 4 interrupt sinks; one per timer channel.
+- clock-frequency : The frequency of the clock that drives the counter, in Hz.
+
+Example:
+
+timer {
+	compatible = "brcm,bcm2835-system-timer";
+	reg = <0x7e003000 0x1000>;
+	interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
+	clock-frequency = <1000000>;
+};

bindings/timer/brcm,kona-timer.txt

@@ -0,0 +1,25 @@
+Broadcom Kona Family timer
+-----------------------------------------------------
+This timer is used in the following Broadcom SoCs:
+ BCM11130, BCM11140, BCM11351, BCM28145, BCM28155
+
+Required properties:
+- compatible : "brcm,kona-timer"
+- DEPRECATED: compatible : "bcm,kona-timer"
+- reg : Register range for the timer
+- interrupts : interrupt for the timer
+- clocks: phandle + clock specifier pair of the external clock
+- clock-frequency: frequency that the clock operates
+
+Only one of clocks or clock-frequency should be specified.
+
+Refer to clocks/clock-bindings.txt for generic clock consumer properties.
+
+Example:
+	timer@35006000 {
+		compatible = "brcm,kona-timer";
+		reg = <0x35006000 0x1000>;
+		interrupts = <0x0 7 0x4>;
+		clocks = <&hub_timer_clk>;
+	};
+

bindings/timer/cadence,ttc-timer.txt

@@ -0,0 +1,21 @@
+Cadence TTC - Triple Timer Counter
+
+Required properties:
+- compatible : Should be "cdns,ttc".
+- reg : Specifies base physical address and size of the registers.
+- interrupts : A list of 3 interrupts; one per timer channel.
+- clocks: phandle to the source clock
+
+Optional properties:
+- timer-width: Bit width of the timer, necessary if not 16.
+
+Example:
+
+ttc0: ttc0@f8001000 {
+	interrupt-parent = <&intc>;
+	interrupts = < 0 10 4 0 11 4 0 12 4 >;
+	compatible = "cdns,ttc";
+	reg = <0xF8001000 0x1000>;
+	clocks = <&cpu_clk 3>;
+	timer-width = <32>;
+};

bindings/timer/cirrus,clps711x-timer.txt

@@ -0,0 +1,29 @@
+* Cirrus Logic CLPS711X Timer Counter
+
+Required properties:
+- compatible: Shall contain "cirrus,ep7209-timer".
+- reg       : Address and length of the register set.
+- interrupts: The interrupt number of the timer.
+- clocks    : phandle of timer reference clock.
+
+Note: Each timer should have an alias correctly numbered in "aliases" node.
+
+Example:
+	aliases {
+		timer0 = &timer1;
+		timer1 = &timer2;
+	};
+
+	timer1: timer@80000300 {
+		compatible = "cirrus,ep7312-timer", "cirrus,ep7209-timer";
+		reg = <0x80000300 0x4>;
+		interrupts = <8>;
+		clocks = <&clks 5>;
+	};
+
+	timer2: timer@80000340 {
+		compatible = "cirrus,ep7312-timer", "cirrus,ep7209-timer";
+		reg = <0x80000340 0x4>;
+		interrupts = <9>;
+		clocks = <&clks 6>;
+	};

bindings/timer/csky,gx6605s-timer.txt

@@ -0,0 +1,42 @@
+=================
+gx6605s SOC Timer
+=================
+
+The timer is used in gx6605s soc as system timer and the driver
+contain clk event and clk source.
+
+==============================
+timer node bindings definition
+==============================
+
+	Description: Describes gx6605s SOC timer
+
+	PROPERTIES
+
+	- compatible
+		Usage: required
+		Value type: <string>
+		Definition: must be "csky,gx6605s-timer"
+	- reg
+		Usage: required
+		Value type: <u32 u32>
+		Definition: <phyaddr size> in soc from cpu view
+	- clocks
+		Usage: required
+		Value type: phandle + clock specifier cells
+		Definition: must be input clk node
+	- interrupt
+		Usage: required
+		Value type: <u32>
+		Definition: must be timer irq num defined by soc
+
+Examples:
+---------
+
+	timer0: timer@20a000 {
+		compatible = "csky,gx6605s-timer";
+		reg = <0x0020a000 0x400>;
+		clocks = <&dummy_apb_clk>;
+		interrupts = <10>;
+		interrupt-parent = <&intc>;
+	};

bindings/timer/csky,mptimer.txt

@@ -0,0 +1,42 @@
+============================
+C-SKY Multi-processors Timer
+============================
+
+C-SKY multi-processors timer is designed for C-SKY SMP system and the
+regs is accessed by cpu co-processor 4 registers with mtcr/mfcr.
+
+ - PTIM_CTLR "cr<0, 14>" Control reg to start reset timer.
+ - PTIM_TSR  "cr<1, 14>" Interrupt cleanup status reg.
+ - PTIM_CCVR "cr<3, 14>" Current counter value reg.
+ - PTIM_LVR  "cr<6, 14>" Window value reg to triger next event.
+
+==============================
+timer node bindings definition
+==============================
+
+	Description: Describes SMP timer
+
+	PROPERTIES
+
+	- compatible
+		Usage: required
+		Value type: <string>
+		Definition: must be "csky,mptimer"
+	- clocks
+		Usage: required
+		Value type: <node>
+		Definition: must be input clk node
+	- interrupts
+		Usage: required
+		Value type: <u32>
+		Definition: must be timer irq num defined by soc
+
+Examples:
+---------
+
+	timer: timer {
+		compatible = "csky,mptimer";
+		clocks = <&dummy_apb_clk>;
+		interrupts = <16>;
+		interrupt-parent = <&intc>;
+	};

bindings/timer/digicolor-timer.txt

@@ -0,0 +1,18 @@
+Conexant Digicolor SoCs Timer Controller
+
+Required properties:
+
+- compatible : should be "cnxt,cx92755-timer"
+- reg : Specifies base physical address and size of the "Agent Communication"
+  timer registers
+- interrupts : Contains 8 interrupts, one for each timer
+- clocks: phandle to the main clock
+
+Example:
+
+	timer@f0000fc0 {
+		compatible = "cnxt,cx92755-timer";
+		reg = <0xf0000fc0 0x40>;
+		interrupts = <19>, <31>, <34>, <35>, <52>, <53>, <54>, <55>;
+		clocks = <&main_clk>;
+	};

bindings/timer/energymicro,efm32-timer.txt

@@ -0,0 +1,23 @@
+* EFM32 timer hardware
+
+The efm32 Giant Gecko SoCs come with four 16 bit timers. Two counters can be
+connected to form a 32 bit counter. Each timer has three Compare/Capture
+channels and can be used as PWM or Quadrature Decoder. Available clock sources
+are the cpu's HFPERCLK (with a 10-bit prescaler) or an external pin.
+
+Required properties:
+- compatible : Should be "energymicro,efm32-timer"
+- reg : Address and length of the register set
+- clocks : Should contain a reference to the HFPERCLK
+
+Optional properties:
+- interrupts : Reference to the timer interrupt
+
+Example:
+
+timer@40010c00 {
+	compatible = "energymicro,efm32-timer";
+	reg = <0x40010c00 0x400>;
+	interrupts = <14>;
+	clocks = <&cmu clk_HFPERCLKTIMER3>;
+};

bindings/timer/ezchip,nps400-timer0.txt

@@ -0,0 +1,17 @@
+NPS Network Processor
+
+Required properties:
+
+- compatible :	should be "ezchip,nps400-timer0"
+
+Clocks required for compatible = "ezchip,nps400-timer0":
+- interrupts : The interrupt of the first timer
+- clocks : Must contain a single entry describing the clock input
+
+Example:
+
+timer {
+	compatible = "ezchip,nps400-timer0";
+	interrupts = <3>;
+	clocks = <&sysclk>;
+};

bindings/timer/ezchip,nps400-timer1.txt

@@ -0,0 +1,15 @@
+NPS Network Processor
+
+Required properties:
+
+- compatible :	should be "ezchip,nps400-timer1"
+
+Clocks required for compatible = "ezchip,nps400-timer1":
+- clocks : Must contain a single entry describing the clock input
+
+Example:
+
+timer {
+	compatible = "ezchip,nps400-timer1";
+	clocks = <&sysclk>;
+};

bindings/timer/faraday,fttmr010.txt

@@ -0,0 +1,37 @@
+Faraday Technology timer
+
+This timer is a generic IP block from Faraday Technology, embedded in the
+Cortina Systems Gemini SoCs and other designs.
+
+Required properties:
+
+- compatible : Must be one of
+  "faraday,fttmr010"
+  "cortina,gemini-timer", "faraday,fttmr010"
+  "moxa,moxart-timer", "faraday,fttmr010"
+  "aspeed,ast2400-timer"
+  "aspeed,ast2500-timer"
+
+- reg : Should contain registers location and length
+- interrupts : Should contain the three timer interrupts usually with
+  flags for falling edge
+
+Optionally required properties:
+
+- clocks : a clock to provide the tick rate for "faraday,fttmr010"
+- clock-names : should be "EXTCLK" and "PCLK" for the external tick timer
+  and peripheral clock respectively, for "faraday,fttmr010"
+- syscon : a phandle to the global Gemini system controller if the compatible
+  type is "cortina,gemini-timer"
+
+Example:
+
+timer@43000000 {
+	compatible = "faraday,fttmr010";
+	reg = <0x43000000 0x1000>;
+	interrupts = <14 IRQ_TYPE_EDGE_FALLING>, /* Timer 1 */
+		   <15 IRQ_TYPE_EDGE_FALLING>, /* Timer 2 */
+		   <16 IRQ_TYPE_EDGE_FALLING>; /* Timer 3 */
+	clocks = <&extclk>, <&pclk>;
+	clock-names = "EXTCLK", "PCLK";
+};

bindings/timer/fsl,ftm-timer.txt

@@ -0,0 +1,31 @@
+Freescale FlexTimer Module (FTM) Timer
+
+Required properties:
+
+- compatible : should be "fsl,ftm-timer"
+- reg : Specifies base physical address and size of the register sets for the
+  clock event device and clock source device.
+- interrupts : Should be the clock event device interrupt.
+- clocks : The clocks provided by the SoC to drive the timer, must contain an
+  entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  o "ftm-evt"
+  o "ftm-src"
+  o "ftm-evt-counter-en"
+  o "ftm-src-counter-en"
+- big-endian: One boolean property, the big endian mode will be in use if it is
+  present, or the little endian mode will be in use for all the device registers.
+
+Example:
+ftm: ftm@400b8000 {
+	compatible = "fsl,ftm-timer";
+	reg = <0x400b8000 0x1000 0x400b9000 0x1000>;
+	interrupts = <0 44 IRQ_TYPE_LEVEL_HIGH>;
+	clock-names = "ftm-evt", "ftm-src",
+		"ftm-evt-counter-en", "ftm-src-counter-en";
+	clocks = <&clks VF610_CLK_FTM2>,
+		<&clks VF610_CLK_FTM3>,
+		<&clks VF610_CLK_FTM2_EXT_FIX_EN>,
+		<&clks VF610_CLK_FTM3_EXT_FIX_EN>;
+	big-endian;
+};

bindings/timer/fsl,gtm.txt

@@ -0,0 +1,30 @@
+* Freescale General-purpose Timers Module
+
+Required properties:
+  - compatible : should be
+    "fsl,<chip>-gtm", "fsl,gtm" for SOC GTMs
+    "fsl,<chip>-qe-gtm", "fsl,qe-gtm", "fsl,gtm" for QE GTMs
+    "fsl,<chip>-cpm2-gtm", "fsl,cpm2-gtm", "fsl,gtm" for CPM2 GTMs
+  - reg : should contain gtm registers location and length (0x40).
+  - interrupts : should contain four interrupts.
+  - clock-frequency : specifies the frequency driving the timer.
+
+Example:
+
+timer@500 {
+	compatible = "fsl,mpc8360-gtm", "fsl,gtm";
+	reg = <0x500 0x40>;
+	interrupts = <90 8 78 8 84 8 72 8>;
+	interrupt-parent = <&ipic>;
+	/* filled by u-boot */
+	clock-frequency = <0>;
+};
+
+timer@440 {
+	compatible = "fsl,mpc8360-qe-gtm", "fsl,qe-gtm", "fsl,gtm";
+	reg = <0x440 0x40>;
+	interrupts = <12 13 14 15>;
+	interrupt-parent = <&qeic>;
+	/* filled by u-boot */
+	clock-frequency = <0>;
+};

bindings/timer/fsl,imxgpt.txt

@@ -0,0 +1,45 @@
+Freescale i.MX General Purpose Timer (GPT)
+
+Required properties:
+
+- compatible : should be one of following:
+  for i.MX1:
+  - "fsl,imx1-gpt";
+  for i.MX21:
+  - "fsl,imx21-gpt";
+  for i.MX27:
+  - "fsl,imx27-gpt", "fsl,imx21-gpt";
+  for i.MX31:
+  - "fsl,imx31-gpt";
+  for i.MX25:
+  - "fsl,imx25-gpt", "fsl,imx31-gpt";
+  for i.MX50:
+  - "fsl,imx50-gpt", "fsl,imx31-gpt";
+  for i.MX51:
+  - "fsl,imx51-gpt", "fsl,imx31-gpt";
+  for i.MX53:
+  - "fsl,imx53-gpt", "fsl,imx31-gpt";
+  for i.MX6Q:
+  - "fsl,imx6q-gpt", "fsl,imx31-gpt";
+  for i.MX6DL:
+  - "fsl,imx6dl-gpt";
+  for i.MX6SL:
+  - "fsl,imx6sl-gpt", "fsl,imx6dl-gpt";
+  for i.MX6SX:
+  - "fsl,imx6sx-gpt", "fsl,imx6dl-gpt";
+- reg : specifies base physical address and size of the registers.
+- interrupts : should be the gpt interrupt.
+- clocks : the clocks provided by the SoC to drive the timer, must contain
+           an entry for each entry in clock-names.
+- clock-names : must include "ipg" entry first, then "per" entry.
+
+Example:
+
+gpt1: timer@10003000 {
+	compatible = "fsl,imx27-gpt", "fsl,imx21-gpt";
+	reg = <0x10003000 0x1000>;
+	interrupts = <26>;
+	clocks = <&clks IMX27_CLK_GPT1_IPG_GATE>,
+		 <&clks IMX27_CLK_PER1_GATE>;
+	clock-names = "ipg", "per";
+};

bindings/timer/img,pistachio-gptimer.txt

@@ -0,0 +1,28 @@
+* Pistachio general-purpose timer based clocksource
+
+Required properties:
+ - compatible: "img,pistachio-gptimer".
+ - reg: Address range of the timer registers.
+ - interrupts: An interrupt for each of the four timers
+ - clocks: Should contain a clock specifier for each entry in clock-names
+ - clock-names: Should contain the following entries:
+                "sys", interface clock
+                "slow", slow counter clock
+                "fast", fast counter clock
+ - img,cr-periph: Must contain a phandle to the peripheral control
+		  syscon node.
+
+Example:
+	timer: timer@18102000 {
+		compatible = "img,pistachio-gptimer";
+		reg = <0x18102000 0x100>;
+		interrupts = <GIC_SHARED 60 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SHARED 61 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SHARED 62 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SHARED 63 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clk_periph PERIPH_CLK_COUNTER_FAST>,
+		         <&clk_periph PERIPH_CLK_COUNTER_SLOW>,
+			 <&cr_periph SYS_CLK_TIMER>;
+		clock-names = "fast", "slow", "sys";
+		img,cr-periph = <&cr_periph>;
+	};

bindings/timer/jcore,pit.txt

@@ -0,0 +1,24 @@
+J-Core Programmable Interval Timer and Clocksource
+
+Required properties:
+
+- compatible: Must be "jcore,pit".
+
+- reg: Memory region(s) for timer/clocksource registers. For SMP,
+  there should be one region per cpu, indexed by the sequential,
+  zero-based hardware cpu number.
+
+- interrupts: An interrupt to assign for the timer. The actual pit
+  core is integrated with the aic and allows the timer interrupt
+  assignment to be programmed by software, but this property is
+  required in order to reserve an interrupt number that doesn't
+  conflict with other devices.
+
+
+Example:
+
+timer@200 {
+	compatible = "jcore,pit";
+	reg = < 0x200 0x30 0x500 0x30 >;
+	interrupts = < 0x48 >;
+};

bindings/timer/lsi,zevio-timer.txt

@@ -0,0 +1,33 @@
+TI-NSPIRE timer
+
+Required properties:
+
+- compatible : should be "lsi,zevio-timer".
+- reg : The physical base address and size of the timer (always first).
+- clocks: phandle to the source clock.
+
+Optional properties:
+
+- interrupts : The interrupt number of the first timer.
+- reg : The interrupt acknowledgement registers
+	(always after timer base address)
+
+If any of the optional properties are not given, the timer is added as a
+clock-source only.
+
+Example:
+
+timer {
+	compatible = "lsi,zevio-timer";
+	reg = <0x900D0000 0x1000>, <0x900A0020 0x8>;
+	interrupts = <19>;
+	clocks = <&timer_clk>;
+};
+
+Example (no clock-events):
+
+timer {
+	compatible = "lsi,zevio-timer";
+	reg = <0x900D0000 0x1000>;
+	clocks = <&timer_clk>;
+};

bindings/timer/marvell,armada-370-xp-timer.txt

@@ -0,0 +1,44 @@
+Marvell Armada 370 and Armada XP Timers
+---------------------------------------
+
+Required properties:
+- compatible: Should be one of the following
+              "marvell,armada-370-timer",
+	      "marvell,armada-375-timer",
+	      "marvell,armada-xp-timer".
+- interrupts: Should contain the list of Global Timer interrupts and
+  then local timer interrupts
+- reg: Should contain location and length for timers register. First
+  pair for the Global Timer registers, second pair for the
+  local/private timers.
+
+Clocks required for compatible = "marvell,armada-370-timer":
+- clocks : Must contain a single entry describing the clock input
+
+Clocks required for compatibles = "marvell,armada-xp-timer",
+				  "marvell,armada-375-timer":
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "nbclk" (L2/coherency fabric clock),
+  "fixed" (Reference 25 MHz fixed-clock).
+
+Examples:
+
+- Armada 370:
+
+	timer {
+		compatible = "marvell,armada-370-timer";
+		reg = <0x20300 0x30>, <0x21040 0x30>;
+		interrupts = <37>, <38>, <39>, <40>, <5>, <6>;
+		clocks = <&coreclk 2>;
+	};
+
+- Armada XP:
+
+	timer {
+		compatible = "marvell,armada-xp-timer";
+		reg = <0x20300 0x30>, <0x21040 0x30>;
+		interrupts = <37>, <38>, <39>, <40>, <5>, <6>;
+		clocks = <&coreclk 2>, <&refclk>;
+		clock-names = "nbclk", "fixed";
+	};

bindings/timer/marvell,orion-timer.txt

@@ -0,0 +1,16 @@
+Marvell Orion SoC timer
+
+Required properties:
+- compatible: shall be "marvell,orion-timer"
+- reg: base address of the timer register starting with TIMERS CONTROL register
+- interrupts: should contain the interrupts for Timer0 and Timer1
+- clocks: phandle of timer reference clock (tclk)
+
+Example:
+	timer: timer {
+		compatible = "marvell,orion-timer";
+		reg = <0x20300 0x20>;
+		interrupt-parent = <&bridge_intc>;
+		interrupts = <1>, <2>;
+		clocks = <&core_clk 0>;
+	};

bindings/timer/mediatek,mtk-timer.txt

@@ -0,0 +1,37 @@
+MediaTek Timers
+---------------
+
+MediaTek SoCs have two different timers on different platforms,
+- GPT (General Purpose Timer)
+- SYST (System Timer)
+
+The proper timer will be selected automatically by driver.
+
+Required properties:
+- compatible should contain:
+	For those SoCs that use GPT
+	* "mediatek,mt2701-timer" for MT2701 compatible timers (GPT)
+	* "mediatek,mt6580-timer" for MT6580 compatible timers (GPT)
+	* "mediatek,mt6589-timer" for MT6589 compatible timers (GPT)
+	* "mediatek,mt7623-timer" for MT7623 compatible timers (GPT)
+	* "mediatek,mt8127-timer" for MT8127 compatible timers (GPT)
+	* "mediatek,mt8135-timer" for MT8135 compatible timers (GPT)
+	* "mediatek,mt8173-timer" for MT8173 compatible timers (GPT)
+	* "mediatek,mt8516-timer" for MT8516 compatible timers (GPT)
+	* "mediatek,mt6577-timer" for MT6577 and all above compatible timers (GPT)
+
+	For those SoCs that use SYST
+	* "mediatek,mt7629-timer" for MT7629 compatible timers (SYST)
+	* "mediatek,mt6765-timer" for MT6765 and all above compatible timers (SYST)
+
+- reg: Should contain location and length for timer register.
+- clocks: Should contain system clock.
+
+Examples:
+
+	timer@10008000 {
+		compatible = "mediatek,mt6577-timer";
+		reg = <0x10008000 0x80>;
+		interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&system_clk>;
+	};

bindings/timer/mrvl,mmp-timer.txt

@@ -0,0 +1,17 @@
+* Marvell MMP Timer controller
+
+Required properties:
+- compatible : Should be "mrvl,mmp-timer".
+- reg : Address and length of the register set of timer controller.
+- interrupts : Should be the interrupt number.
+
+Optional properties:
+- clocks : Should contain a single entry describing the clock input.
+
+Example:
+	timer0: timer@d4014000 {
+		compatible = "mrvl,mmp-timer";
+		reg = <0xd4014000 0x100>;
+		interrupts = <13>;
+		clocks = <&coreclk 2>;
+	};

bindings/timer/nuvoton,npcm7xx-timer.txt

@@ -0,0 +1,21 @@
+Nuvoton NPCM7xx timer
+
+Nuvoton NPCM7xx have three timer modules, each timer module provides five 24-bit
+timer counters.
+
+Required properties:
+- compatible      : "nuvoton,npcm750-timer" for Poleg NPCM750.
+- reg             : Offset and length of the register set for the device.
+- interrupts      : Contain the timer interrupt with flags for
+                    falling edge.
+- clocks          : phandle of timer reference clock (usually a 25 MHz clock).
+
+Example:
+
+timer@f0008000 {
+    compatible = "nuvoton,npcm750-timer";
+    interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+    reg = <0xf0008000 0x50>;
+    clocks = <&clk NPCM7XX_CLK_TIMER>;
+};
+

bindings/timer/nvidia,tegra20-timer.txt

@@ -0,0 +1,24 @@
+NVIDIA Tegra20 timer
+
+The Tegra20 timer provides four 29-bit timer channels and a single 32-bit free
+running counter. The first two channels may also trigger a watchdog reset.
+
+Required properties:
+
+- compatible : should be "nvidia,tegra20-timer".
+- reg : Specifies base physical address and size of the registers.
+- interrupts : A list of 4 interrupts; one per timer channel.
+- clocks : Must contain one entry, for the module clock.
+  See ../clocks/clock-bindings.txt for details.
+
+Example:
+
+timer {
+	compatible = "nvidia,tegra20-timer";
+	reg = <0x60005000 0x60>;
+	interrupts = <0 0 0x04
+			0 1 0x04
+			0 41 0x04
+			0 42 0x04>;
+	clocks = <&tegra_car 132>;
+};

bindings/timer/nvidia,tegra210-timer.txt

@@ -0,0 +1,36 @@
+NVIDIA Tegra210 timer
+
+The Tegra210 timer provides fourteen 29-bit timer counters and one 32-bit
+timestamp counter. The TMRs run at either a fixed 1 MHz clock rate derived
+from the oscillator clock (TMR0-TMR9) or directly at the oscillator clock
+(TMR10-TMR13). Each TMR can be programmed to generate one-shot, periodic,
+or watchdog interrupts.
+
+Required properties:
+- compatible : "nvidia,tegra210-timer".
+- reg : Specifies base physical address and size of the registers.
+- interrupts : A list of 14 interrupts; one per each timer channels 0 through
+  13.
+- clocks : Must contain one entry, for the module clock.
+  See ../clocks/clock-bindings.txt for details.
+
+timer@60005000 {
+	compatible = "nvidia,tegra210-timer";
+	reg = <0x0 0x60005000 0x0 0x400>;
+	interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&tegra_car TEGRA210_CLK_TIMER>;
+	clock-names = "timer";
+};

bindings/timer/nvidia,tegra30-timer.txt

@@ -0,0 +1,28 @@
+NVIDIA Tegra30 timer
+
+The Tegra30 timer provides ten 29-bit timer channels, a single 32-bit free
+running counter, and 5 watchdog modules. The first two channels may also
+trigger a legacy watchdog reset.
+
+Required properties:
+
+- compatible : For Tegra30, must contain "nvidia,tegra30-timer".  Otherwise,
+  must contain '"nvidia,<chip>-timer", "nvidia,tegra30-timer"' where
+  <chip> is tegra124 or tegra132.
+- reg : Specifies base physical address and size of the registers.
+- interrupts : A list of 6 interrupts; one per each of timer channels 1
+    through 5, and one for the shared interrupt for the remaining channels.
+- clocks : Must contain one entry, for the module clock.
+  See ../clocks/clock-bindings.txt for details.
+
+timer {
+	compatible = "nvidia,tegra30-timer", "nvidia,tegra20-timer";
+	reg = <0x60005000 0x400>;
+	interrupts = <0 0 0x04
+		      0 1 0x04
+		      0 41 0x04
+		      0 42 0x04
+		      0 121 0x04
+		      0 122 0x04>;
+	clocks = <&tegra_car 214>;
+};

bindings/timer/nxp,lpc3220-timer.txt

@@ -0,0 +1,26 @@
+* NXP LPC3220 timer
+
+The NXP LPC3220 timer is used on a wide range of NXP SoCs. This
+includes LPC32xx, LPC178x, LPC18xx and LPC43xx parts.
+
+Required properties:
+- compatible:
+	Should be "nxp,lpc3220-timer".
+- reg:
+	Address and length of the register set.
+- interrupts:
+	Reference to the timer interrupt
+- clocks:
+	Should contain a reference to timer clock.
+- clock-names:
+	Should contain "timerclk".
+
+Example:
+
+timer1: timer@40085000 {
+	compatible = "nxp,lpc3220-timer";
+	reg = <0x40085000 0x1000>;
+	interrupts = <13>;
+	clocks = <&ccu1 CLK_CPU_TIMER1>;
+	clock-names = "timerclk";
+};

bindings/timer/nxp,tpm-timer.txt

@@ -0,0 +1,28 @@
+NXP Low Power Timer/Pulse Width Modulation Module (TPM)
+
+The Timer/PWM Module (TPM) supports input capture, output compare,
+and the generation of PWM signals to control electric motor and power
+management applications. The counter, compare and capture registers
+are clocked by an asynchronous clock that can remain enabled in low
+power modes. TPM can support global counter bus where one TPM drives
+the counter bus for the others, provided bit width is the same.
+
+Required properties:
+
+- compatible :	should be "fsl,imx7ulp-tpm"
+- reg :		Specifies base physical address and size of the register sets
+		for the clock event device and clock source device.
+- interrupts :	Should be the clock event device interrupt.
+- clocks :	The clocks provided by the SoC to drive the timer, must contain
+		an entry for each entry in clock-names.
+- clock-names : Must include the following entries: "ipg" and "per".
+
+Example:
+tpm5: tpm@40260000 {
+	compatible = "fsl,imx7ulp-tpm";
+	reg = <0x40260000 0x1000>;
+	interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&clks IMX7ULP_CLK_NIC1_BUS_DIV>,
+		 <&clks IMX7ULP_CLK_LPTPM5>;
+	clock-names = "ipg", "per";
+};

bindings/timer/oxsemi,rps-timer.txt

@@ -0,0 +1,17 @@
+Oxford Semiconductor OXNAS SoCs Family RPS Timer
+================================================
+
+Required properties:
+- compatible: Should be "oxsemi,ox810se-rps-timer" or "oxsemi,ox820-rps-timer"
+- reg : Specifies base physical address and size of the registers.
+- interrupts : The interrupts of the two timers
+- clocks : The phandle of the timer clock source
+
+example:
+
+timer0: timer@200 {
+	compatible = "oxsemi,ox810se-rps-timer";
+	reg = <0x200 0x40>;
+	clocks = <&rpsclk>;
+	interrupts = <4 5>;
+};

bindings/timer/qcom,msm-timer.txt

@@ -0,0 +1,47 @@
+* MSM Timer
+
+Properties:
+
+- compatible : Should at least contain "qcom,msm-timer". More specific
+               properties specify which subsystem the timers are paired with.
+
+               "qcom,kpss-timer" - krait subsystem
+               "qcom,scss-timer" - scorpion subsystem
+
+- interrupts : Interrupts for the debug timer, the first general purpose
+               timer, and optionally a second general purpose timer, and
+               optionally as well, 2 watchdog interrupts, in that order.
+
+- reg : Specifies the base address of the timer registers.
+
+- clocks: Reference to the parent clocks, one per output clock. The parents
+          must appear in the same order as the clock names.
+
+- clock-names: The name of the clocks as free-form strings. They should be in
+               the same order as the clocks.
+
+- clock-frequency : The frequency of the debug timer and the general purpose
+                    timer(s) in Hz in that order.
+
+Optional:
+
+- cpu-offset : per-cpu offset used when the timer is accessed without the
+               CPU remapping facilities. The offset is
+               cpu-offset + (0x10000 * cpu-nr).
+
+Example:
+
+       timer@200a000 {
+               compatible = "qcom,scss-timer", "qcom,msm-timer";
+               interrupts = <1 1 0x301>,
+                            <1 2 0x301>,
+                            <1 3 0x301>,
+                            <1 4 0x301>,
+                            <1 5 0x301>;
+               reg = <0x0200a000 0x100>;
+               clock-frequency = <19200000>,
+                                 <32768>;
+               clocks = <&sleep_clk>;
+               clock-names = "sleep";
+               cpu-offset = <0x40000>;
+       };

bindings/timer/rda,8810pl-timer.txt

@@ -0,0 +1,20 @@
+RDA Micro RDA8810PL Timer
+
+Required properties:
+- compatible      :  "rda,8810pl-timer"
+- reg             :  Offset and length of the register set for the device.
+- interrupts      :  Should contain two interrupts.
+- interrupt-names :  Should be "hwtimer", "ostimer".
+
+Example:
+
+		apb@20900000 {
+			compatible = "simple-bus";
+			...
+			timer@10000 {
+				compatible = "rda,8810pl-timer";
+				reg = <0x10000 0x1000>;
+				interrupts = <16 IRQ_TYPE_LEVEL_HIGH>,
+					     <17 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "hwtimer", "ostimer";
+			};

bindings/timer/renesas,16bit-timer.txt

@@ -0,0 +1,25 @@
+* Renesas H8/300 16bit timer
+
+The 16bit timer is a 16bit timer/counter with configurable clock inputs and
+programmable compare match.
+
+Required Properties:
+
+  - compatible: must contain "renesas,16bit-timer"
+  - reg: base address and length of the registers block for the timer module.
+  - interrupts: interrupt-specifier for the timer, IMIA
+  - clocks: a list of phandle, one for each entry in clock-names.
+  - clock-names: must contain "peripheral_clk" for the functional clock.
+  - renesas,channel: timer channel number.
+
+Example:
+
+	timer16: timer@ffff68 {
+		compatible = "reneas,16bit-timer";
+		reg = <0xffff68 8>, <0xffff60 8>;
+		interrupts = <24>;
+		renesas,channel = <0>;
+		clocks = <&pclk>;
+		clock-names = "peripheral_clk";
+	};
+

bindings/timer/renesas,8bit-timer.txt

@@ -0,0 +1,25 @@
+* Renesas H8/300 8bit timer
+
+The 8bit timer is a 8bit timer/counter with configurable clock inputs and
+programmable compare match.
+
+This implement only supported cascade mode.
+
+Required Properties:
+
+  - compatible: must contain "renesas,8bit-timer"
+  - reg: base address and length of the registers block for the timer module.
+  - interrupts: interrupt-specifier for the timer, CMIA and TOVI
+  - clocks: a list of phandle, one for each entry in clock-names.
+  - clock-names: must contain "fck" for the functional clock.
+
+Example:
+
+	timer8_0: timer@ffff80 {
+		compatible = "renesas,8bit-timer";
+		reg = <0xffff80 10>;
+		interrupts = <36>;
+		clocks = <&fclk>;
+		clock-names = "fck";
+	};
+

bindings/timer/renesas,cmt.txt

@@ -0,0 +1,96 @@
+* Renesas R-Car Compare Match Timer (CMT)
+
+The CMT is a multi-channel 16/32/48-bit timer/counter with configurable clock
+inputs and programmable compare match.
+
+Channels share hardware resources but their counter and compare match value
+are independent. A particular CMT instance can implement only a subset of the
+channels supported by the CMT model. Channel indices represent the hardware
+position of the channel in the CMT and don't match the channel numbers in the
+datasheets.
+
+Required Properties:
+
+  - compatible: must contain one or more of the following:
+    - "renesas,cmt-48-sh73a0" for the sh73A0 48-bit CMT
+		(CMT1)
+    - "renesas,cmt-48-r8a7740" for the r8a7740 48-bit CMT
+		(CMT1)
+    - "renesas,cmt-48" for all non-second generation 48-bit CMT
+		(CMT1 on sh73a0 and r8a7740)
+		This is a fallback for the above renesas,cmt-48-* entries.
+
+    - "renesas,r8a73a4-cmt0" for the 32-bit CMT0 device included in r8a73a4.
+    - "renesas,r8a73a4-cmt1" for the 48-bit CMT1 device included in r8a73a4.
+    - "renesas,r8a7743-cmt0" for the 32-bit CMT0 device included in r8a7743.
+    - "renesas,r8a7743-cmt1" for the 48-bit CMT1 device included in r8a7743.
+    - "renesas,r8a7744-cmt0" for the 32-bit CMT0 device included in r8a7744.
+    - "renesas,r8a7744-cmt1" for the 48-bit CMT1 device included in r8a7744.
+    - "renesas,r8a7745-cmt0" for the 32-bit CMT0 device included in r8a7745.
+    - "renesas,r8a7745-cmt1" for the 48-bit CMT1 device included in r8a7745.
+    - "renesas,r8a77470-cmt0" for the 32-bit CMT0 device included in r8a77470.
+    - "renesas,r8a77470-cmt1" for the 48-bit CMT1 device included in r8a77470.
+    - "renesas,r8a774a1-cmt0" for the 32-bit CMT0 device included in r8a774a1.
+    - "renesas,r8a774a1-cmt1" for the 48-bit CMT1 device included in r8a774a1.
+    - "renesas,r8a774c0-cmt0" for the 32-bit CMT0 device included in r8a774c0.
+    - "renesas,r8a774c0-cmt1" for the 48-bit CMT1 device included in r8a774c0.
+    - "renesas,r8a7790-cmt0" for the 32-bit CMT0 device included in r8a7790.
+    - "renesas,r8a7790-cmt1" for the 48-bit CMT1 device included in r8a7790.
+    - "renesas,r8a7791-cmt0" for the 32-bit CMT0 device included in r8a7791.
+    - "renesas,r8a7791-cmt1" for the 48-bit CMT1 device included in r8a7791.
+    - "renesas,r8a7793-cmt0" for the 32-bit CMT0 device included in r8a7793.
+    - "renesas,r8a7793-cmt1" for the 48-bit CMT1 device included in r8a7793.
+    - "renesas,r8a7794-cmt0" for the 32-bit CMT0 device included in r8a7794.
+    - "renesas,r8a7794-cmt1" for the 48-bit CMT1 device included in r8a7794.
+    - "renesas,r8a7796-cmt0" for the 32-bit CMT0 device included in r8a7796.
+    - "renesas,r8a7796-cmt1" for the 48-bit CMT1 device included in r8a7796.
+    - "renesas,r8a77970-cmt0" for the 32-bit CMT0 device included in r8a77970.
+    - "renesas,r8a77970-cmt1" for the 48-bit CMT1 device included in r8a77970.
+    - "renesas,r8a77980-cmt0" for the 32-bit CMT0 device included in r8a77980.
+    - "renesas,r8a77980-cmt1" for the 48-bit CMT1 device included in r8a77980.
+
+    - "renesas,rcar-gen2-cmt0" for 32-bit CMT0 devices included in R-Car Gen2
+		and RZ/G1.
+    - "renesas,rcar-gen2-cmt1" for 48-bit CMT1 devices included in R-Car Gen2
+		and RZ/G1.
+		These are fallbacks for r8a73a4, R-Car Gen2 and RZ/G1 entries
+		listed above.
+    - "renesas,rcar-gen3-cmt0" for 32-bit CMT0 devices included in R-Car Gen3
+		and RZ/G2.
+    - "renesas,rcar-gen3-cmt1" for 48-bit CMT1 devices included in R-Car Gen3
+		and RZ/G2.
+		These are fallbacks for R-Car Gen3 and RZ/G2 entries listed
+		above.
+
+  - reg: base address and length of the registers block for the timer module.
+  - interrupts: interrupt-specifier for the timer, one per channel.
+  - clocks: a list of phandle + clock-specifier pairs, one for each entry
+    in clock-names.
+  - clock-names: must contain "fck" for the functional clock.
+
+
+Example: R8A7790 (R-Car H2) CMT0 and CMT1 nodes
+
+	cmt0: timer@ffca0000 {
+		compatible = "renesas,r8a7790-cmt0", "renesas,rcar-gen2-cmt0";
+		reg = <0 0xffca0000 0 0x1004>;
+		interrupts = <0 142 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 142 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp1_clks R8A7790_CLK_CMT0>;
+		clock-names = "fck";
+	};
+
+	cmt1: timer@e6130000 {
+		compatible = "renesas,r8a7790-cmt1", "renesas,rcar-gen2-cmt1";
+		reg = <0 0xe6130000 0 0x1004>;
+		interrupts = <0 120 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 121 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 122 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 123 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 124 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 125 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 126 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 127 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp3_clks R8A7790_CLK_CMT1>;
+		clock-names = "fck";
+	};

bindings/timer/renesas,mtu2.txt

@@ -0,0 +1,42 @@
+* Renesas Multi-Function Timer Pulse Unit 2 (MTU2)
+
+The MTU2 is a multi-purpose, multi-channel timer/counter with configurable
+clock inputs and programmable compare match.
+
+Channels share hardware resources but their counter and compare match value
+are independent. The MTU2 hardware supports five channels indexed from 0 to 4.
+
+Required Properties:
+
+  - compatible: must be one or more of the following:
+    - "renesas,mtu2-r7s72100" for the r7s72100 MTU2
+    - "renesas,mtu2" for any MTU2
+      This is a fallback for the above renesas,mtu2-* entries
+
+  - reg: base address and length of the registers block for the timer module.
+
+  - interrupts: interrupt specifiers for the timer, one for each entry in
+    interrupt-names.
+  - interrupt-names: must contain one entry named "tgi?a" for each enabled
+    channel, where "?" is the channel index expressed as one digit from "0" to
+    "4".
+
+  - clocks: a list of phandle + clock-specifier pairs, one for each entry
+    in clock-names.
+  - clock-names: must contain "fck" for the functional clock.
+
+
+Example: R7S72100 (RZ/A1H) MTU2 node
+
+	mtu2: timer@fcff0000 {
+		compatible = "renesas,mtu2-r7s72100", "renesas,mtu2";
+		reg = <0xfcff0000 0x400>;
+		interrupts = <0 139 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 146 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 150 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 154 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 159 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "tgi0a", "tgi1a", "tgi2a", "tgi3a", "tgi4a";
+		clocks = <&mstp3_clks R7S72100_CLK_MTU2>;
+		clock-names = "fck";
+	};

bindings/timer/renesas,ostm.txt

@@ -0,0 +1,31 @@
+* Renesas OS Timer (OSTM)
+
+The OSTM is a multi-channel 32-bit timer/counter with fixed clock
+source that can operate in either interval count down timer or free-running
+compare match mode.
+
+Channels are independent from each other.
+
+Required Properties:
+
+  - compatible: must be one or more of the following:
+    - "renesas,r7s72100-ostm" for the R7S72100 (RZ/A1) OSTM
+    - "renesas,r7s9210-ostm" for the R7S9210 (RZ/A2) OSTM
+    - "renesas,ostm" for any OSTM
+		This is a fallback for the above renesas,*-ostm entries
+
+  - reg: base address and length of the register block for a timer channel.
+
+  - interrupts: interrupt specifier for the timer channel.
+
+  - clocks: clock specifier for the timer channel.
+
+Example: R7S72100 (RZ/A1H) OSTM node
+
+	ostm0: timer@fcfec000 {
+		compatible = "renesas,r7s72100-ostm", "renesas,ostm";
+		reg = <0xfcfec000 0x30>;
+		interrupts = <GIC_SPI 102 IRQ_TYPE_EDGE_RISING>;
+		clocks = <&mstp5_clks R7S72100_CLK_OSTM0>;
+		power-domains = <&cpg_clocks>;
+	};

bindings/timer/renesas,tmu.txt

@@ -0,0 +1,47 @@
+* Renesas R-Mobile/R-Car Timer Unit (TMU)
+
+The TMU is a 32-bit timer/counter with configurable clock inputs and
+programmable compare match.
+
+Channels share hardware resources but their counter and compare match value
+are independent. The TMU hardware supports up to three channels.
+
+Required Properties:
+
+  - compatible: must contain one or more of the following:
+    - "renesas,tmu-r8a7740" for the r8a7740 TMU
+    - "renesas,tmu-r8a774c0" for the r8a774C0 TMU
+    - "renesas,tmu-r8a7778" for the r8a7778 TMU
+    - "renesas,tmu-r8a7779" for the r8a7779 TMU
+    - "renesas,tmu-r8a77970" for the r8a77970 TMU
+    - "renesas,tmu-r8a77980" for the r8a77980 TMU
+    - "renesas,tmu" for any TMU.
+      This is a fallback for the above renesas,tmu-* entries
+
+  - reg: base address and length of the registers block for the timer module.
+
+  - interrupts: interrupt-specifier for the timer, one per channel.
+
+  - clocks: a list of phandle + clock-specifier pairs, one for each entry
+    in clock-names.
+  - clock-names: must contain "fck" for the functional clock.
+
+Optional Properties:
+
+  - #renesas,channels: number of channels implemented by the timer, must be 2
+    or 3 (if not specified the value defaults to 3).
+
+
+Example: R8A7779 (R-Car H1) TMU0 node
+
+	tmu0: timer@ffd80000 {
+		compatible = "renesas,tmu-r8a7779", "renesas,tmu";
+		reg = <0xffd80000 0x30>;
+		interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 33 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 34 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp0_clks R8A7779_CLK_TMU0>;
+		clock-names = "fck";
+
+		#renesas,channels = <3>;
+	};

bindings/timer/renesas,tpu.txt

@@ -0,0 +1,21 @@
+* Renesas H8/300 Timer Pulse Unit
+
+The TPU is a 16bit timer/counter with configurable clock inputs and
+programmable compare match.
+This implementation support only cascade mode.
+
+Required Properties:
+
+  - compatible: must contain "renesas,tpu"
+  - reg: base address and length of the registers block in 2 channel.
+  - clocks: a list of phandle, one for each entry in clock-names.
+  - clock-names: must contain "peripheral_clk" for the functional clock.
+
+
+Example:
+	tpu: tpu@ffffe0 {
+		compatible = "renesas,tpu";
+		reg = <0xffffe0 16>, <0xfffff0 12>;
+		clocks = <&pclk>;
+		clock-names = "peripheral_clk";
+	};

bindings/timer/rockchip,rk-timer.txt

@@ -0,0 +1,27 @@
+Rockchip rk timer
+
+Required properties:
+- compatible: should be:
+  "rockchip,rv1108-timer", "rockchip,rk3288-timer": for Rockchip RV1108
+  "rockchip,rk3036-timer", "rockchip,rk3288-timer": for Rockchip RK3036
+  "rockchip,rk3066-timer", "rockchip,rk3288-timer": for Rockchip RK3066
+  "rockchip,rk3188-timer", "rockchip,rk3288-timer": for Rockchip RK3188
+  "rockchip,rk3228-timer", "rockchip,rk3288-timer": for Rockchip RK3228
+  "rockchip,rk3229-timer", "rockchip,rk3288-timer": for Rockchip RK3229
+  "rockchip,rk3288-timer": for Rockchip RK3288
+  "rockchip,rk3368-timer", "rockchip,rk3288-timer": for Rockchip RK3368
+  "rockchip,rk3399-timer": for Rockchip RK3399
+- reg: base address of the timer register starting with TIMERS CONTROL register
+- interrupts: should contain the interrupts for Timer0
+- clocks : must contain an entry for each entry in clock-names
+- clock-names : must include the following entries:
+  "timer", "pclk"
+
+Example:
+	timer: timer@ff810000 {
+		compatible = "rockchip,rk3288-timer";
+		reg = <0xff810000 0x20>;
+		interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&xin24m>, <&cru PCLK_TIMER>;
+		clock-names = "timer", "pclk";
+	};

bindings/timer/samsung,exynos4210-mct.txt

@@ -0,0 +1,88 @@
+Samsung's Multi Core Timer (MCT)
+
+The Samsung's Multi Core Timer (MCT) module includes two main blocks, the
+global timer and CPU local timers. The global timer is a 64-bit free running
+up-counter and can generate 4 interrupts when the counter reaches one of the
+four preset counter values. The CPU local timers are 32-bit free running
+down-counters and generate an interrupt when the counter expires. There is
+one CPU local timer instantiated in MCT for every CPU in the system.
+
+Required properties:
+
+- compatible: should be "samsung,exynos4210-mct".
+  (a) "samsung,exynos4210-mct", for mct compatible with Exynos4210 mct.
+  (b) "samsung,exynos4412-mct", for mct compatible with Exynos4412 mct.
+
+- reg: base address of the mct controller and length of the address space
+  it occupies.
+
+- interrupts: the list of interrupts generated by the controller. The following
+  should be the order of the interrupts specified. The local timer interrupts
+  should be specified after the four global timer interrupts have been
+  specified.
+
+	0: Global Timer Interrupt 0
+	1: Global Timer Interrupt 1
+	2: Global Timer Interrupt 2
+	3: Global Timer Interrupt 3
+	4: Local Timer Interrupt 0
+	5: Local Timer Interrupt 1
+	6: ..
+	7: ..
+	i: Local Timer Interrupt n
+
+  For MCT block that uses a per-processor interrupt for local timers, such
+  as ones compatible with "samsung,exynos4412-mct", only one local timer
+  interrupt might be specified, meaning that all local timers use the same
+  per processor interrupt.
+
+Example 1: In this example, the IP contains two local timers, using separate
+	   interrupts, so two local timer interrupts have been specified,
+	   in addition to four global timer interrupts.
+
+	mct@10050000 {
+		compatible = "samsung,exynos4210-mct";
+		reg = <0x10050000 0x800>;
+		interrupts = <0 57 0>, <0 69 0>, <0 70 0>, <0 71 0>,
+			     <0 42 0>, <0 48 0>;
+	};
+
+Example 2: In this example, the timer interrupts are connected to two separate
+	   interrupt controllers. Hence, an interrupt-map is created to map
+	   the interrupts to the respective interrupt controllers.
+
+	mct@101c0000 {
+		compatible = "samsung,exynos4210-mct";
+		reg = <0x101C0000 0x800>;
+		interrupt-parent = <&mct_map>;
+		interrupts = <0>, <1>, <2>, <3>, <4>, <5>;
+
+		mct_map: mct-map {
+			#interrupt-cells = <1>;
+			#address-cells = <0>;
+			#size-cells = <0>;
+			interrupt-map = <0 &gic 0 57 0>,
+					<1 &gic 0 69 0>,
+					<2 &combiner 12 6>,
+					<3 &combiner 12 7>,
+					<4 &gic 0 42 0>,
+					<5 &gic 0 48 0>;
+		};
+	};
+
+Example 3: In this example, the IP contains four local timers, but using
+	   a per-processor interrupt to handle them. Either all the local
+	   timer interrupts can be specified, with the same interrupt specifier
+	   value or just the first one.
+
+	mct@10050000 {
+		compatible = "samsung,exynos4412-mct";
+		reg = <0x10050000 0x800>;
+
+		/* Both ways are possible in this case. Either: */
+		interrupts = <0 57 0>, <0 69 0>, <0 70 0>, <0 71 0>,
+			     <0 42 0>;
+		/* or: */
+		interrupts = <0 57 0>, <0 69 0>, <0 70 0>, <0 71 0>,
+			     <0 42 0>, <0 42 0>, <0 42 0>, <0 42 0>;
+	};

bindings/timer/snps,arc-timer.txt

@@ -0,0 +1,27 @@
+Synopsys ARC Local Timer with Interrupt Capabilities
+- Found on all ARC CPUs (ARC700/ARCHS)
+- Can be optionally programmed to interrupt on Limit
+- Two idential copies TIMER0 and TIMER1 exist in ARC cores and historically
+  TIMER0 used as clockevent provider (true for all ARC cores)
+  TIMER1 used for clocksource (mandatory for ARC700, optional for ARC HS)
+
+Required properties:
+
+- compatible : should be "snps,arc-timer"
+- interrupts : single Interrupt going into parent intc
+	       (16 for ARCHS cores, 3 for ARC700 cores)
+- clocks     : phandle to the source clock
+
+Example:
+
+	timer0 {
+		compatible = "snps,arc-timer";
+		interrupts = <3>;
+		interrupt-parent = <&core_intc>;
+		clocks = <&core_clk>;
+	};
+
+	timer1 {
+		compatible = "snps,arc-timer";
+		clocks = <&core_clk>;
+	};

bindings/timer/snps,archs-gfrc.txt

@@ -0,0 +1,14 @@
+Synopsys ARC Free Running 64-bit Global Timer for ARC HS CPUs
+- clocksource provider for SMP SoC
+
+Required properties:
+
+- compatible : should be "snps,archs-gfrc"
+- clocks     : phandle to the source clock
+
+Example:
+
+	gfrc {
+		compatible = "snps,archs-gfrc";
+		clocks = <&core_clk>;
+	};

bindings/timer/snps,archs-rtc.txt

@@ -0,0 +1,14 @@
+Synopsys ARC Free Running 64-bit Local Timer for ARC HS CPUs
+- clocksource provider for UP SoC
+
+Required properties:
+
+- compatible : should be "snps,archs-rtc"
+- clocks     : phandle to the source clock
+
+Example:
+
+	rtc {
+		compatible = "snps,arc-rtc";
+		clocks = <&core_clk>;
+	};

bindings/timer/socionext,milbeaut-timer.txt

@@ -0,0 +1,17 @@
+Milbeaut SoCs Timer Controller
+
+Required properties:
+
+- compatible : should be "socionext,milbeaut-timer".
+- reg : Specifies base physical address and size of the registers.
+- interrupts : The interrupt of the first timer.
+- clocks: phandle to the input clk.
+
+Example:
+
+timer {
+	compatible = "socionext,milbeaut-timer";
+	reg = <0x1e000050 0x20>
+	interrupts = <0 91 4>;
+	clocks = <&clk 4>;
+};

bindings/timer/spreadtrum,sprd-timer.txt

@@ -0,0 +1,20 @@
+Spreadtrum timers
+
+The Spreadtrum SC9860 platform provides 3 general-purpose timers.
+These timers can support 32bit or 64bit counter, as well as supporting
+period mode or one-shot mode, and they are can be wakeup source
+during deep sleep.
+
+Required properties:
+- compatible: should be "sprd,sc9860-timer" for SC9860 platform.
+- reg: The register address of the timer device.
+- interrupts: Should contain the interrupt for the timer device.
+- clocks: The phandle to the source clock (usually a 32.768 KHz fixed clock).
+
+Example:
+	timer@40050000 {
+		compatible = "sprd,sc9860-timer";
+		reg = <0 0x40050000 0 0x20>;
+		interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&ext_32k>;
+	};

bindings/timer/st,spear-timer.txt

@@ -0,0 +1,16 @@
+* SPEAr ARM Timer
+
+** Timer node required properties:
+
+- compatible : Should be:
+	"st,spear-timer"
+- reg: Address range of the timer registers
+- interrupt: Should contain the timer interrupt number
+
+Example:
+
+	timer@f0000000 {
+		compatible = "st,spear-timer";
+		reg = <0xf0000000 0x400>;
+		interrupts = <2>;
+	};

bindings/timer/st,stih407-lpc

@@ -0,0 +1,28 @@
+STMicroelectronics Low Power Controller (LPC) - Clocksource
+===========================================================
+
+LPC currently supports Watchdog OR Real Time Clock OR Clocksource
+functionality.
+
+[See: ../watchdog/st_lpc_wdt.txt for Watchdog options]
+[See: ../rtc/rtc-st-lpc.txt for RTC options]
+
+Required properties
+
+- compatible   : Must be: "st,stih407-lpc"
+- reg          : LPC registers base address + size
+- interrupts   : LPC interrupt line number and associated flags
+- clocks       : Clock used by LPC device (See: ../clock/clock-bindings.txt)
+- st,lpc-mode  : The LPC can run either one of three modes:
+                  ST_LPC_MODE_RTC    [0]
+                  ST_LPC_MODE_WDT    [1]
+                  ST_LPC_MODE_CLKSRC [2]
+		 One (and only one) mode must be selected.
+
+Example:
+       lpc@fde05000 {
+               compatible      = "st,stih407-lpc";
+               reg             = <0xfde05000 0x1000>;
+               clocks          = <&clk_s_d3_flexgen CLK_LPC_0>;
+               st,lpc-mode     = <ST_LPC_MODE_CLKSRC>;
+       };

bindings/timer/st,stm32-timer.txt

@@ -0,0 +1,22 @@
+. STMicroelectronics STM32 timer
+
+The STM32 MCUs family has several general-purpose 16 and 32 bits timers.
+
+Required properties:
+- compatible : Should be "st,stm32-timer"
+- reg : Address and length of the register set
+- clocks : Reference on the timer input clock
+- interrupts : Reference to the timer interrupt
+
+Optional properties:
+- resets: Reference to a reset controller asserting the timer
+
+Example:
+
+timer5: timer@40000c00 {
+	compatible = "st,stm32-timer";
+	reg = <0x40000c00 0x400>;
+	interrupts = <50>;
+	resets = <&rrc 259>;
+	clocks = <&clk_pmtr1>;
+};

bindings/timer/stericsson-u300-apptimer.txt

@@ -0,0 +1,18 @@
+ST-Ericsson U300 apptimer
+
+Required properties:
+
+- compatible : should be "stericsson,u300-apptimer"
+- reg : Specifies base physical address and size of the registers.
+- interrupts : A list of 4 interrupts; one for each subtimer. These
+  are, in order: OS (operating system), DD (device driver) both
+  adopted for EPOC/Symbian with two specific IRQs for these tasks,
+  then GP1 and GP2, which are general-purpose timers.
+
+Example:
+
+timer {
+	compatible = "stericsson,u300-apptimer";
+	reg = <0xc0014000 0x1000>;
+	interrupts = <24 25 26 27>;
+};

bindings/timer/ti,c64x+timer64.txt

@@ -0,0 +1,25 @@
+Timer64
+-------
+
+The timer64 node describes C6X event timers.
+
+Required properties:
+
+- compatible: must be "ti,c64x+timer64"
+- reg: base address and size of register region
+- interrupts: interrupt id
+
+Optional properties:
+
+- ti,dscr-dev-enable: Device ID used to enable timer IP through DSCR interface.
+
+- ti,core-mask: on multi-core SoCs, bitmask of cores allowed to use this timer.
+
+Example:
+	timer0: timer@25e0000 {
+		compatible = "ti,c64x+timer64";
+		ti,core-mask = < 0x01 >;
+		reg = <0x25e0000 0x40>;
+		interrupt-parent = <&megamod_pic>;
+		interrupts = < 16 >;
+	};

bindings/timer/ti,davinci-timer.txt

@@ -0,0 +1,37 @@
+* Device tree bindings for Texas Instruments DaVinci timer
+
+This document provides bindings for the 64-bit timer in the DaVinci
+architecture devices. The timer can be configured as a general-purpose 64-bit
+timer, dual general-purpose 32-bit timers. When configured as dual 32-bit
+timers, each half can operate in conjunction (chain mode) or independently
+(unchained mode) of each other.
+
+The timer is a free running up-counter and can generate interrupts when the
+counter reaches preset counter values.
+
+Also see ../watchdog/davinci-wdt.txt for timers that are configurable as
+watchdog timers.
+
+Required properties:
+
+- compatible : should be "ti,da830-timer".
+- reg : specifies base physical address and count of the registers.
+- interrupts : interrupts generated by the timer.
+- interrupt-names: should be "tint12", "tint34", "cmpint0", "cmpint1",
+		   "cmpint2", "cmpint3", "cmpint4", "cmpint5", "cmpint6",
+		   "cmpint7" ("cmpintX" may be omitted if not present in the
+		   hardware).
+- clocks : the clock feeding the timer clock.
+
+Example:
+
+	clocksource: timer@20000 {
+		compatible = "ti,da830-timer";
+		reg = <0x20000 0x1000>;
+		interrupts = <21>, <22>, <74>, <75>, <76>, <77>, <78>, <79>,
+			     <80>, <81>;
+		interrupt-names = "tint12", "tint34", "cmpint0", "cmpint1",
+				  "cmpint2", "cmpint3", "cmpint4", "cmpint5",
+				  "cmpint6", "cmpint7";
+		clocks = <&pll0_auxclk>;
+	};

bindings/timer/ti,keystone-timer.txt

@@ -0,0 +1,29 @@
+* Device tree bindings for Texas instruments Keystone timer
+
+This document provides bindings for the 64-bit timer in the KeyStone
+architecture devices. The timer can be configured as a general-purpose 64-bit
+timer, dual general-purpose 32-bit timers. When configured as dual 32-bit
+timers, each half can operate in conjunction (chain mode) or independently
+(unchained mode) of each other.
+
+It is global timer is a free running up-counter and can generate interrupt
+when the counter reaches preset counter values.
+
+Documentation:
+http://www.ti.com/lit/ug/sprugv5a/sprugv5a.pdf
+
+Required properties:
+
+- compatible : should be "ti,keystone-timer".
+- reg : specifies base physical address and count of the registers.
+- interrupts : interrupt generated by the timer.
+- clocks : the clock feeding the timer clock.
+
+Example:
+
+timer@22f0000 {
+	compatible = "ti,keystone-timer";
+	reg = <0x022f0000 0x80>;
+	interrupts = <GIC_SPI 110 IRQ_TYPE_EDGE_RISING>;
+	clocks = <&clktimer15>;
+};

bindings/timer/ti,timer.txt

@@ -0,0 +1,44 @@
+OMAP Timer bindings
+
+Required properties:
+- compatible:		Should be set to one of the below. Please note that
+			OMAP44xx devices have timer instances that are 100%
+			register compatible with OMAP3xxx devices as well as
+			newer timers that are not 100% register compatible.
+			So for OMAP44xx devices timer instances may use
+			different compatible strings.
+
+			ti,omap2420-timer (applicable to OMAP24xx devices)
+			ti,omap3430-timer (applicable to OMAP3xxx/44xx devices)
+			ti,omap4430-timer (applicable to OMAP44xx devices)
+			ti,omap5430-timer (applicable to OMAP543x devices)
+			ti,am335x-timer	(applicable to AM335x devices)
+			ti,am335x-timer-1ms (applicable to AM335x devices)
+
+- reg:			Contains timer register address range (base address and
+			length).
+- interrupts: 		Contains the interrupt information for the timer. The
+			format is being dependent on which interrupt controller
+			the OMAP device uses.
+- ti,hwmods:		Name of the hwmod associated to the timer, "timer<X>",
+			where <X> is the instance number of the timer from the
+			HW spec.
+
+Optional properties:
+- ti,timer-alwon:	Indicates the timer is in an alway-on power domain.
+- ti,timer-dsp:		Indicates the timer can interrupt the on-chip DSP in
+			addition to the ARM CPU.
+- ti,timer-pwm: 	Indicates the timer can generate a PWM output.
+- ti,timer-secure: 	Indicates the timer is reserved on a secure OMAP device
+			and therefore cannot be used by the kernel.
+
+Example:
+
+timer12: timer@48304000 {
+	compatible = "ti,omap3430-timer";
+	reg = <0x48304000 0x400>;
+	interrupts = <95>;
+	ti,hwmods = "timer12"
+	ti,timer-alwon;
+	ti,timer-secure;
+};

bindings/timer/via,vt8500-timer.txt

@@ -0,0 +1,15 @@
+VIA/Wondermedia VT8500 Timer
+-----------------------------------------------------
+
+Required properties:
+- compatible : "via,vt8500-timer"
+- reg : Should contain 1 register ranges(address and length)
+- interrupts : interrupt for the timer
+
+Example:
+
+	timer@d8130100 {
+		compatible = "via,vt8500-timer";
+		reg = <0xd8130100 0x28>;
+		interrupts = <36>;
+	};