Jishnu Prakash
db169cc515
dt-bindings: qpnp-lcdb-regulator: Add support for some LCDB DT properties
...
Add support for the following LCDB devicee tree properties:
"qcom,high-p2-blank-time-ns" to control the higher clamp threshold for
p2 minimum on time.
"qcom,low-p2-blank-time-ns" to control the lower clamp threshold for
p2 minimum on time.
"qcom,mpc-current-thr-ma" to control the mpc threshold for inductor
current after start up is done.
Change-Id: Ibc095328035bb52899846587e3db711a5c8296f2
2023-04-13 14:02:37 +08:00
Jishnu Prakash
6366d0e47c
dt-bindings: qpnp-lcdb-regulator: Add support for NCP symmetry with LDO
...
Add a device-tree property which enables NCP symmetry. This
configuration in HW enables the NCP voltage to follow LDO.
Change-Id: Ie97eb8b6a4eff96e78ef7f90688b1f5e3fd84133
2023-04-13 14:02:04 +08:00
Jishnu Prakash
2dfd7b50c4
dt-bindings: qpnp-lcdb-regulator: Add support for PM7325B LCDB
...
Add compatible string for PM7325B LCDB device. Remove pmic-revid
property as it is not used on kernel 5.4. Add pwrup-delay-ms,
qcom,bst-ps-threshold-mv and qcom,pwrup-config properties for PM7325B.
Update qcom,bst-ilim-ma, qcom,ncp-ilim-ma and qcom,ldo-ilim-ma for
PM7325B.
Change-Id: I66b3bfd1782f41eb44cca08adce2a02bada0727c
2023-04-13 13:58:49 +08:00
qctecmdr
c0a3beeed1
Merge "bindings: regulator: add bindings for diodes,ap72200"
2023-03-17 16:31:31 -07:00
Umang Chheda
22c0b570cb
bindings: regulator: add bindings for diodes,ap72200
...
AP72200 is a high-current synchronous buck-boost converter providing
high efficiency, excellent transient response, and high DC output accuracy.
It operates with a 2.3-5.4V Input range and Outputs 2.6-5.14V.
Add the bindings necessary to describe it.
Change-Id: I2cdf2dbdb3e95c6b7029d697930bb46cf7d97707
2023-03-16 19:21:54 +05:30
Jishnu Prakash
1d3bf9c896
dt-bindings: rpmh-regulator: Add support for PBS RPMh resources
...
PBS RPMh resources are used to trigger PBS sequences, which
may be used to toggle the enable state of regulators which are
required to be controlled by HW enable option.
Add support for them.
Change-Id: I33c57e6b78ccdbbf626f8d219e4b3b632aaeb653
2023-03-06 21:51:30 -08:00
Jishnu Prakash
360a7adf8c
dt-bindings: regulator: add disable-mode for rpmh-regulator
...
Add an optional property "qcom,disable-mode" for LDOs which gets
set when they get disabled and removed when they are re-enabled, to
avoid unexpected high power consumption when they are disabled and
the mode gets set from another subsystem.
Change-Id: Ie0173335d7574fb9e71daa1ee878d20bc32d8904
2022-08-11 11:35:02 +05:30
Jagadeesh Kona
52f0506e6e
bindings: regulator: gdsc: Add support for qcom,clk-ctrl bindings
...
Add support for qcom,clk-ctrl bindings to enable/disable few clocks
before GDSC enable/disable.
Change-Id: Idf10902362b940e45758fcfe5aaa563a5b72d53d
2022-07-31 21:23:16 -07:00
qctecmdr
c64140a9e0
Merge "dt-bindings: regulator: Add documentation for GDSC DT properties"
2022-07-29 09:01:03 -07:00
Kalpak Kawadkar
48982e1ee7
dt-bindings: regulator: Add documentation for GDSC DT properties
...
Add documentation for sw-reset, hw-ctrl-addr, domain-addr and
no-config-gdscr GDSC DT properties.
Change-Id: Ibebe06c40b74a396cdd765ae5e3a5dd771dce128
2022-07-22 02:47:37 -07:00
David Collins
d9bba50525
dt-bindings: regulator: add QTI OCP notifier bindings documentation
...
Add a bindings documentation file for QTI regulator over-current
(OCP) notifier devices. These devices can be used to monitor and
notifier consumers of regulator OCP events on certain Qualcomm
Technologies, Inc. PMICs.
Change-Id: Id86cf62144c6e9f970cd09b7fe7a93ab40ef6cd8
2022-07-19 02:37:34 -07:00
Kalpak Kawadkar
e359db2e79
dt-bindings: regulator: gdsc-regulator: Add qcom,collapse-vote property
...
Add documentation for qcom,collapse-vote property, which can be used
for specifying the votable registers to control the GDSC operations.
Change-Id: Ie0f5699bd2859a286ede20592a3b7cbbb7e97175
2022-05-26 16:16:02 +05:30
David Collins
7f161bfdf2
dt-bindings: regulator: pm8008-regulator: add PM8010 support
...
Add support for the PM8010 PMIC. PM8010 is a pin-compatible
update of PM8008.
Change-Id: Ia3d83b87e5124d99d3ebf3ff2fd797938f2f75b3
2021-06-08 14:36:50 -07:00
Elliot Berman
7adfb2b429
ARM: dts: msm: Merge kernel.lnx.5.4-200915 into msm-5.10
...
Merge kernel.lnx.5.4-200915 into msm-5.10.
Change-Id: If85db2d0b92b484f2e439d72bee8c5e1056baa3f
2020-12-17 06:33:10 -08:00
Elliot Berman
b54d17c2f5
bindings: Merge android-mainline (cbf07d5) into msm-waipio
...
Merge snapshot of bindings from android-mainline commit cbf07d5
("FROMLIST: clk: sunxi-ng: add support for the Allwinner A100 CCU").
Change-Id: Ica9bc8abf055fb28bdcd33dad244e3ba5fe1a04b
2020-09-23 13:47:05 -07:00
qctecmdr
f82e10852f
Merge "dt-bindings: Add support for GDSC flag to skip disable"
2020-09-13 21:34:16 -07:00
Naveen Yadav
02878921f6
dt-bindings: Add support for GDSC flag to skip disable
...
Add new gdsc flag "qcom,skip-disable-before-sw-enable" to skip
the GDSC disable call in case if the gdsc is enabled by entity
external to HLOS.
Change-Id: I2519c1b7a36a5b89df1a92c1c39f5f3413927548
2020-08-04 10:36:34 +05:30
Jishnu Prakash
54d43ac4bb
dt-bindings: regulator: Add optional RPM-SMD regulator properties
...
Add "qcom,min-dropout-voltage" to specify the min dropout voltage
for RPM-SMD regulators, "qcom,supported-modes" to specify supported
BOB regulator modes and "qcom,mode-threshold-currents" to specify
minimum allowed currents for supported BOB modes.
Change-Id: Ife7ce8d1e506b41fce8079b0424fbf71dc874d50
2020-07-28 11:04:16 +05:30
Elliot Berman
936530a982
Merge tag 'kernel.lnx.5.4-200510' into msm-waipio
...
* tag 'kernel.lnx.5.4-200510':
ARM: dts: msm: Add cooling-cells property in battery device for lahaina
ARM: dts: msm: Add hyp core control driver node for Lahaina
ARM: dts: msm: Add PMIC die temperature mitigation for Lahaina
ARM: dts: msm: Add modem junction mitigation rule for Lahaina
dt-bindings: qcom-pmic-gpio: Add PM7250B, PM6350 and PM6150L bindings
ARM: dts: msm: Add QUPv3 and GPI DT nodes on SHIMA
ARM: dts: msm: Add Modem pil node for Shima
ARM: dts: msm: add stub interconnect devices for sm8150
dt-bindings: interconnect: add interconnect bindings
ARM: dts: msm: enable superspeed plus redriver on QRD
ARM: dts: msm: set io coherent on cvp DT
ARM: dts: msm: Add CDSP pil node for Shima
ARM: dts: msm: Add LPASS pil node for Shima
dt-bindings: interconnect: add interconnect bindings
dt-bindings: regulator: Add snapshot of rpm-smd-regulator doc
ARM: dts: msm: Remove unused PMK8350 ADC channels for holi
ARM: dts: msm: Add stub regulators for sdx65
ARM: dts: msm: Add usb bypass mode and disable smmu for lahaina
ARM: dts: msm: Add DT snapshots for PM6350, PM7250b and PM6150l
ARM: dts: msm: usb_phy pin support usb_phy and gpio mode
ARM: dts: msm: Add SPMI PMIC arbiter device for holi
ARM: dts: msm: Mark USB DP/DM interrupt as dual edge on Lahaina
dt-bindings: Add support for event RP access from DDR for GPI and GCI
ARM: dts: msm: Add RUMI specific console property for Shima
ARM: dts: msm: Add QUPv3_0 and SE5 dt nodes for SHIMA
ARM: dts: msm: clean up cache-size properties
ARM: dts: msm: Add kernel cmdline to increase the dmesg buffer size
ARM: dts: msm: Change TUI heap type to MSM_CARVEOUT
ARM: dts: msm: Add modem ADC thermistors for Lahaina
dt-bindings: thermal: Add support for mmw ADC thermistors
ARM: dts: msm: Enable CDSP cooling devices for Lahaina
ARM: dts: msm: Enable uC HOLB monitor feature
ARM: dts: msm: Add initial ION heaps for holi
ARM: dts: msm: Add memory map for holi
ARM: dts: msm: Adding external VR viewer support
ARM: dts: msm: add qcom,ipa-gpi_event_rp_ddr property
ARM: dts: msm: Add secure_buffer and qcom,scm device on SM8150
ARM: dts: msm: Add initial ION heaps for SM8150
ARM: dts: msm: Add qrtr haven for trusted vm
ARM: dts: msm: Add qrtr haven for lahaina
ARM: dts: msm: Add neuron block service for trusted vm
ARM: dts: msm: Add neuron block service for lahaina
ARM: dts: msm: Add dts node for boot_stats
ARM: dts: msm: Add TLMM direct connect interrupts for sm8150
dt-bindings: Add dt-binding for mpm counter
ARM: dts: msm: Increase memory-hotplug region for lahaina
dt-bindings: thermal: Add support for modem DSC cooling devices
dt-bindings: thermal: Add support for CDSP cooling devices via qmi cdev
ARM: dts: qcom: add dt entry needed for avb
ARM: dts: msm: Add missing compatible of cmd_db for shima
ARM: dts: msm: Add dummy clock nodes for clock controllers for HOLI
bindings: clock: Add support for HOLI clock controller
ARM: dts: msm: Add system_pm as child of APPS RSC for shima
ARM: dts: msm: add nvmem cell for haptics CL brake in Lahaina
Revert "Revert "ARM: dts: msm: increase ipa modem smem size to 36k on Lahaina""
ARM: dts: msm: Add SPS node for Shima
ARM: dts: msm: add sleep state for PCIe0 CLKREQ for lahaina
ARM: dts: msm: Add the mem-buf device for the trusted VM
ARM: dts: msm: Add modem DSC mitigation nodes for lahaina
ARM: dts: msm: Enable IO coherency with USB device on Lahaina
ARM: dts: msm: Add UFS support for shima
ARM: dts: msm: Enable SD card on Lahaina QRD platform
ARM: dts: msm: Update gpio drive strength for soundwire tx
ARM: dts: msm: Add stub regulators for holi
ARM: dts: msm: Adding device tree node for holi pinctrl
dt-bindings: Adding pinctrl devicetree binding for holi
ARM: dts: msm: Add initial device tree for Holi
ARM: dts: msm: add smmu devices for Shima
ARM: dts: msm: Add DMA coherency hint to vidc context banks
Revert "ARM: dts: msm: increase ipa modem smem size to 36k on Lahaina"
ARM: dts: msm: Update ddr bandwidth levels for A660
ARM: dts: msm: Add ARM PMU node for Shima
ARM: dts: msm: Add SLPI pinctrl for SM8150
bindings: pinctrl: Add device-tree bindings for SLPI pinctrl driver
bindings: input: qcom-hv-haptics: add nvmem to store CL brake settings
bindings: input: qcom-hv-haptics: Add qcom,fifo-empty-threshold
ARM: dts: msm: Add clock required for IPA QoS configuration
ARM: dts: msm: Add LLCC entry for Shima
ARM: dts: msm: Add ipcc test nodes for Shima
ARM: dts: msm: add PDR support for PMIC Glink on Lahaina
bindings: pmic-glink: add protection domain restart (PDR) support
ARM: dts: msm: do not compile Non-VM specific DT files
ARM: dts: msm: Update QMP Phy init sequence for Lahaina
ARM: dts: msm: Add dcc registers lists for lahaina
ARM: dts: msm: Update the RPMHCC node for SHIMA
ARM: dts: msm: Modify voltage ranges for PM8350B AMOLED regulator
dt-bindings: qpnp-amoled: Update voltage ranges for PM8150A/PM8350B
ARM: dts: msm: Remove NFC I3C DT node for Lahaina
ARM: dts: msm: Add clocks for UFS QOS configuration on Lahaina
ARM: dts: msm: use voltage mitigation for pop mem in lahaina
ARM: dts: msm: Enable CPU voltage cooling device for lahaina
dt-bindings: thermal: Use the correct vendor string for voltage device
ARM: dts: msm: add stub interconnect devices for SHIMA
dt-bindings: Add documentation for the "non-coherent" SMMU dt-binding
dt-bindings: interconnect: add interconnect bindings
ARM: dts: msm: Add charger reference to USB node on Lahaina
dt-bindings: i2c-msm-geni: Add DT bindings for le-vm flag
ARM: dts: qcom: reduce PM8008J LDO min voltages for Lahaina
ARM: dts: msm: Add support for votable GDSCs
ARM: dts: msm: Remove epss_l3_shared node
bindings: clock: Add support for SHIMA clock controllers
ARM: dts: msm: Add IMEM entry for Shima
ARM: dts: msm: Add device trees for LahainaP variant
dt-bindings: msm: Add compatible strings for lahainap
ARM: dts: msm: Add Common driver, I2C and GSI DT nodes in trustedvm
ARM: dts: msm: add capacity and DPC properties for Shima
ARM: dts: msm: Add LPM support for sm8150
ARM: dts: msm: Update RSC nodes for sm8150
ARM: dts: msm: Update PDC node for sm8150
ARM: dts: msm: Add "regulator-allow-set-load" for PM8350B IBB regulator
dt-bindings: LLCC: Add "qcom,shima-llcc" compatible property
ARM: dts: msm: increase ipa modem smem size to 36k on Lahaina
ARM: dts: msm: Update ufs bus vote for Lahaina
ARM: dts: msm: Add USB nodes for Shima
dt-bindings: thermal: Add documentation for CPU voltage cooling device
ARM: dts: msm: Disable tpdm ddr for lahaina
ARM: dts: msm: Add cdsp rpmsg entry in Lahaina
ARM: dts: msm: Add spss glink ssr entry for Lahaina
dt-bindings: usb: Add Gen2 Tx Compliance tuning property for dwc3
ARM: dts: msm: Add entry for bluetooth sw_ctrl gpio
ARM: dts: msm: Increase the dwc3 reg address range for Lahaina
Revert "ARM: dts: msm: Clean-up vidc DT node"
ARM: dts: msm: Add pinctrl for PM8350C GPIO 9 on Lahaina platforms
ARM: dts: msm: Add pshold to Shima
ARM: dts: msm: add msm_rtb tracing
ARM: dts: msm: Add core hang detection to dt for Shima
ARM: dts: msm: Move qbt_handler to soc
ARM: dts: msm: Add boot-enabled flag support for spcom
ARM: dts: msm: Add boot-enabled flag support for spss
ARM: dts: msm: use 'dma-coherent-hint-cached' for fastrpc nodes
Revert "dt-bindings: msm: vidc: Clean-up dt properties"
ARM: dts: msm: Enable smmu for SD card on Lahaina
ARM: dts: msm: remove aux devices
dt-bindings: clock: Add rpmh clock bindings for Shima
ARM: dts: msm: Add regulators for sa8155
ARM: dts: msm: Remove spss glink ssr entry for Lahaina
ARM: dts: msm: add proxy consumers for L2B and L1C regulators on Lahaina
dt-bindings: net: Add bindings for qcom,qrtr-haven
ARM: dts: msm: Set no-status-check-on-disable for Lahaina PCIe GDSCs
ARM: dts: msm: Add snapshot of all SM8150 and SA8155 DT files
ARM: dts: msm: enable qmap flow control feature
ARM: dts: msm: Add RSC device bindings for Shima
ARM: dts: msm: Add wakeup parent for Shima TLMM
ARM: dts: msm: add PDC device bindings for Shima
ARM: dts: msm: Add support for ION for the trusted-VM
ARM: dts: msm: add swr dmic's as codecs
bindings: sound: Add swr-haptics binding document
ARM: dts: msm: define continuous splash memory region for lahaina
dt-bindings: msm: Add compatible strings for sa8155
ARM: dts: msm: Add initial device tree for SM8150
ARM: dts: msm: Add LPM support for shima
ARM: dts: msm: add subsystem restart (SSR) for PMIC Glink on Lahaina
dt-bindings: pmic-glink: add subsystem restart (SSR) support
dt-bindings: qpnp-lcdb-regulator: Add LCDB regulator documentation
ARM: dts: msm: Add labels for lpi_cx and lpi_mx rails
ARM: dts: msm: Enable UFS HS Rate-B on Lahaina
ARM: dts: msm: add FE CPU dai for hearing aid
ARM: dts: msm: Add AMOLED regulator on pm8350b for Lahaina
ARM: dts: msm: Enable CPU cooling device for lahaina
dt-bindings: Add support for boot enabled subsystem
bindings: input: qcom-hv-haptics: Change to use 8-bit FIFO data
ARM: dts: msm: Add swr-slave regulator device node in haptics module
bindings: input: qcom-hv-haptics: add swr-slave regulator subnode
ARM: dts: msm: Add AOP QMP nodes for shima
ARM: dts: msm: Add glink entries for Shima
ARM: dts: msm: Add HWSPINLOCK, SMEM and SMP2P for Shima
ARM: dts: msm: Add IPCC node for Shima
ARM: dts: msm: Add initial ION heaps for Shima
ARM: dts: msm: Add spss glink ssr entry for Lahaina
ARM: dts: msm: add 4 new compute DSP context banks for lahaina
ARM: dts: qcom: modify initramfs size
ARM: dts: msm: Add memory map for shima
ARM: dts: msm: Add EUD extcon handler for primary USB on Lahaina
ARM: dts: msm: Set dr_mode as OTG on Lahaina
ARM: dts: msm: add node for Atmel touch on Lahaina
bindings: spmi: spmi-pmic-arb: define consumer qcom,pmic-arb property
ARM: dts: msm: add UCSI connector and USB port on Lahaina
ARM: dts: msm: add CPU dai for additional proxy ports
ARM: dts: msm: Fix the dc_noc io register space and size
ARM: dts: msm: Add pinctrls for external regulaors in camera for Lahaina
ARM: dts: msm: Map QDSS gfx debug registers for Lahaina
ARM: dts: msm: Add apb clock to GPU device for Lahaina
ARM: dts: msm: Update disp_bcm_voter to only wait for AMC
ARM: dts: msm: add wil6210 device for Lahaina platforms
ARM: dts: qcom: add sde-rsc-rpmh driver to disp_rsc node
ARM: dts: msm: Enable Kryo erp driver for Shima
ARM: dts: msm: Manage rumi identification with platform flag
ARM: dts: msm: add node for Focaltech touch on Lahaina
ARM: dts: msm: add gpio cells property
bindings: spmi: spmi-pmic-arb: mark interrupt properties as optional
Revert "ARM: dts: msm: change camera DTSI inclusions for Lahaina qrd"
ARM: dts: msm: change camera DTSI inclusions for Lahaina qrd
ARM: dts: msm: Update QMP Phy init sequence for Lahaina
ARM: dts: msm: Add SCM node for Shima
ARM: dts: msm: Update all gdsc time out to 500 us
ARM: dts: msm: add pinctrl for secondary display for lahaina
ARM: dts: msm: add wsa883x as codecs
ARM: dts: msm: add wcd938x as a codec
ARM: dts: msm: Correct sleep clk frequency to 32khz
dt-bindings: net: Add bindings for qcom,neuron
ARM: dts: msm: Add configuration for vref regulator vote for lahaina
ARM: dts: msm: Add GPU thermal zone configuration for lahaina
ARM: dts: msm: Add BCL configuration for lahaina
ARM: dts: msm: Add CPU thermal configuration for lahaina
bindings: Add dt-bindings for pdc controller on qc SoCs
bindings: ARM: add devicetree binding for describing PSCI firmware
bindings: Add snapshot of dt bindings for arm-cache
bindings: Add dt-bindings for arch_timer
dt-bindings: Add compatible strings for rmph clk for sm8150
dt-bindings: Add compatible strings for gcc clock on sm8150
dt-bindings: msm: Add compatible strings for sa5155
dt-bindings: Add snapshot of hyp_core_ctl driver documentation
ARM: dts: msm: Update the GSI gpii mask for lahaina
ARM: dts: msm: add msm id in shima-rumi-overlay.dts
dt-bindings: leds-qpnp-vibrator-ldo: Add vibrator LDO documentation
ARM: dts: msm: Add pin configuration for USB3 PHY portselect
dt-bindings: usb: Add super speed re-driver bindings
ARM: dts: msm: Enable LPM and remove the gear limits on Lahaina
dt-bindings: msm: vidc: Clean-up dt properties
ARM: dts: msm: Add modem QMI sensor and cdev configuration for lahaina
dt-bindings: thermal: Add LMH DCVSh devicetree documentation
ARM: dts: msm: add charger thermal mitigation levels for Lahaina MTP
ARM: dts: msm: Clean-up vidc DT node
ARM: dts: msm: Update CNSS S12B voltage level to 1.35v
ARM: dts: msm: Enable smmu for ufs on Lahaina
ARM: dts: msm: Upgrade Lahaina's memory map to version 4
ARM: dts: msm: Add the mem-buf device for Lahaina
ARM: dts: msm: remove CX, MX and MMCX always-on configuration for Lahaina
Change-Id: I99734e502f1611c3d3a4652815fc4701348e2f7b
2020-07-10 10:00:48 -07:00
qctecmdr
841db05cbe
Merge "dt-bindings: qpnp-amoled: add support to configure single phase for IBB"
2020-05-13 04:46:52 -07:00
Venkata Narendra Kumar Gutta
229b528f41
Merge tag 'kernel.lnx.5.4-200305.1' into msm-waipio
...
* tag 'kernel.lnx.5.4-200305.1':
ARM: dts: msm: Add the CX GDSC to the IOMMU device
ARM: dts: msm: Move IOMMU clocks to the GPU device
ARM: dts: msm: Enable USB secondary port on Lahaina
bindings: power: supply: Add thermal mitigation for qcom,battery-charger
ARM: dts: msm: Add dummy clock nodes for clock controllers for SHIMA
ARM: dts: msm: enable haptics for Lahaina QRD
ARM: dts: msm: Update S12B and S1C voltages
ARM: dts: msm: add support for dynamic port map
ARM: dts: msm: add wil6210 pinctrl configurations for Lahaina
ARM: dts: msm: Add NFC I3C device node for Lahaina
ARM: dts: msm: Enable SD card support on Lahaina
ARM: dts: msm: Add SD card bus voting details for Lahaina
ARM: dts: msm: Add CVP AXI reset pulse
ARM: dts: msm: Add stub regulators for shima
ARM: dts: msm: add route between va and swr dmic's
Revert "ARM: dts: msm: remove hdmi codec enable"
ARM: dts: msm: update SWR_DMIC to 0 on Lahaina QRD device
ARM: dts: msm: Mark APPS SMMU interconnect votes as active-only
dt-bindings: Document qcom,active-only
ARM: dts: qcom: Update trusted vm DT entries
ARM: dts: msm: Add pinctrl node for TLMM on Shima SoC
bindings: pinctrl: Add device-tree bindings for Shima pinctrl driver
ARM: dts: msm: Add initial device tree for Shima
ARM: dts: msm: Correct cmb size of turing llm turing for lahaina
ARM: dts: msm: add DMIC DT node for QRD DMIC device
ARM: dts: msm: Add camera device tree inclusions for Lahaina
ARM: dts: qcom: specify ADC channels for Lahaina PMIC temp-alarm devices
ARM: dts: msm: Update devicetree to enable FM on lahaina
ARM: dts: msm: Add ADC support for Lahaina
ARM: dts: msm: set PMIC thermal zone trip points to critical for Lahaina
ARM: dts: msm: Update S12B and S1C voltages
ARM: dts: msm: Add fix for SW_CTRL mapped to wrong GPIO66 on MSM side
ARM: dts: msm: remove hdmi codec enable
ARM: dts: msm: add external audio codec
ARM: dts: msm: Correct the interconnect names node
ARM: dts: msm: Open up gpu power levels upto NOM
ARM: dts: msm: Add hwkm node for lahaina
bindings: Add device-tree bindings for hwkm driver
ARM: dts: msm: Add camera device tree inclusions for Lahaina
ARM: dts: msm: Add WLAN updates to HSP DTSI overlays
ARM: dts: msm: Add ICE region for UFS
ARM: dts: msm: update PCIe0 and PCIe1 PHY for lahaina v1
ARM: dts: msm: Fix FM chip ON issue
ARM: dts: msm: Add snapshot of memshare dt documentation
ARM: dts: msm: Add support for FM in lahaina platform
dt-bindings: thermal: qcom-adc-tm: add PMIC7 ADC_TM_IIO compatible string
dt-bindings: msm: add snapshot of msm_11ad doc
ARM: dts: msm: add swr dmics as aux dev
ARM: dts: msm: Update CNSS S12B voltage level to 1.35v
ARM: dts: msm: Update soundwire DMIC configuration on Lahaina
ARM: dts: msm: update PCIe0 and PCIe1 CLKREQ default func select on lahaina
ARM: dts: msm: Add dt node for Focaltech touch IC
ARM: dts: msm: Add tpdm lpass lpi for lahaina
ARM: dts: msm: Add cti trig_out gpio for Lahaina
ARM: dts: msm: Add dt node for ST Micro touch IC
ARM: dts: msm: add gpio pincntrl for touch
ARM: dts: msm: fix DSI reset gpio pincntrl
ARM: dts: msm: update audio dt node for lahaina qrd device
ARM: dts: qcom: Add regulator changes for Lahaina
ARM: dts: msm: Reorganize the pinctrl node
ARM: dts: qcom: Rename lahaina-svm1 to trustedvm
ARM: dts: msm: update i2c slave address for fsa4480 on Lahaina
ARM: dts: msm: Add a new device tree file for HSP configuration
ARM: dts: msm: Add VBUS/ID configuration for USB secondary port on Lahaina
ARM: dts: msm: update audio device tree on lahaina
ARM: dts: msm: Add usb_audio_qmi_dev node
ARM: dts: msm: Fix the gem_noc node address and reg size
ARM: dts: msm: Disable tpdm shrm for Lahaina
ARM: dts: msm: Enable turing llm tpdm for lahaina
ARM: dts: msm: Add mem_dump node for lahaina
ARM: dts: msm: disable second USB port for Lahaina QRD
dt-bindings: haven: Add bindings for qcom,vm-1.0
ARM: dts: msm: Rectify I3C node DT properties
ARM: dts: qcom: add flash/torch LEDs on PM8350C for Lahaina platforms
ARM: dts: msm: Disable USB secondary port on Lahaina
ARM: dts: qcom: Reserved GuestVM memory and add its PIL driver
dt-bindings: Add bindings for guestvm-loader
ARM: dts: msm: Add permittable RFA2 (min,max) voltage
ARM: dts: msm: Limit ETR iova range for lahaina
ARM: dts: msm: Add IPCC test nodes for end to end verification
ARM: dts: msm: Add CNSS2 node for Lahaina
ARM: dts: msm: Update dtsi for page recycle and cleanup
ARM: dts: qcom: update RPMh regulator min/max voltage limits for Lahaina
ARM: dts: msm: update PCIe L5 and L6 current vote on lahaina
ARM: dts: msm: Add Altmode PMIC GLINK client for Lahaina
bindings: Add altmode-glink
ARM: dts: msm: Restrict default CMA region below 0xE0000000
ARM: dts: qcom: add Glink SPMI debug controller device for Lahaina
ARM: dts: msm: include display platform DT files
bindings: spmi: add QTI Glink SPMI debug controller binding documentation
ARM: dts: msm: add proxy votes for display regulators
arm64: dts: qcom: Add secondary VM dts file for lahaina
ARM: dts: msm: Correct the typo of remote-endpoint for lahaina
ARM: dts: msm: limit gear to 3 for Lahaina
ARM: dts: qcom: add haptics on PM8350B for Lahaina CDP/MTP
ARM: dts: msm: Update Lahaina USB3 QMP UNI PHY init settings
ARM: dts: msm: Hot fix for Lahaina
ARM: dts: qcom: Link restart_reason nvmem cell to qcom,pshold
ARM: dts: qcom: add nvmem cell for PMK8350 SDAM2 restart reason
ARM: dts: msm: enable PCIe0 and PCIe1 on lahaina
dt-bindings: Document the qcom,dynamic-heap binding
dt-bindings: Add device-tree bindings for the memory sharing driver
ARM: dts: msm: add PMIC Glink and clients for Lahaina
ARM: dts: msm: Update fastrpc SIDs and masks
ARM: dts: qcom: add VDD_MX and CX subnodes for MMCX dependencies on Lahaina
ARM: dts: msm: Enable video driver
ARM: dts: qcom: Update limit-rate and add limit-phy-submode on Lahaina
ARM: dts: msm: set MSR range in CSR for Lahaina
dt-bindings: extcon-usb-gpio: Document optional vbus-out-gpio
ARM: dts: msm: Update changes for audio device tree on Lahaina
ARM: dts: msm: Fix secondary USB port related aggre_noc clock
ARM: dts: msm: add initial PHY sequence for PCIe0 and PCIe1 on lahaina
ARM: dts: msm: add PCIe pipe clk mux and ext src to PCIe clock for lahaina
ARM: dts: msm: add aggre_noc_pcie_*_axi_clk for PCIe on lahaina
ARM: dts: msm: Add dtsi changes for qbt_handler
dt-bindings: Add documentation for qbt_handler
ARM: dts: msm: Add TSENS thermal nodes for lahaina
ARM: dts: qcom: change all rpmh-regulator LDO default modes to HPM
ARM: dts: msm: Do not create logical mappings for the secure CDSP heap
ARM: dts: msm: Disable watchdog for Lahaina-RUMI
ARM: dts: msm: Update the arch_timer frequency
ARM: dts: msm: Specify address/size cells for &soc on lahaina-rumi
dt-bindings: input: qcom-hv-haptics: Add initial binding document
ARM: dts: msm: Add secure display heap
ARM: dts: msm: Add alias for HSUART node
ARM: dts: qcom: switch to I2C control of PM8008 PMIC regulators for Lahaina
ARM: dts: msm: Include ipcc_test dtsi file in lahaina.dtsi file
ARM: dts: msm: vidc: Add register value mask
ARM: dts: msm: Fix ufs OCS error
ARM: dts: msm: Fix USB PHY resets
ARM: dts: msm: Add interconnects to USB on Lahaina
dt-bindings: usb: Document interconnects usage for qcom,dwc-usb3-msm
bindings: qti-flash: Fix slave id for pm8350c in DT example
dt-bindings: Add snapshot of QPNP AMOLED regulator bindings
bindings: soc: qcom: add QTI battery glink debug
ARM: dts: msm: Add PWM and RGB LED devices for PM8350C
ARM: dts: msm: add a CX, MX and MMCX Turbo level proxy request for Lahaina
ARM: dts: qcom: update RPMh regulator voltage limits for Lahaina
ARM: dts: msm: Add QSEE IRQ bridge entry for Lahaina
ARM: dts: msm: Add device tree overlay for Lahaina CDP
ARM: dts: msm: Add regulator entries for Lahaina
ARM: dts: msm: add qcom,fastrpc-gids property on Lahaina
ARM: dts: msm: Update supply routing for swr dmic on Lahaina
bindings: pinctrl: Add device-tree bindings for Lahaina pinctrl driver
ARM: dts: msm: add display sde nodes to target dtsi
ARM: dts: msm: Replace swr dmic mic bias number on Lahaina
bindings: Documentation: Update swr mic device tree documentation
ARM: dts: msm: Add and enable disp rsc support for Lahaina
ARM: dts: msm: add proxy consumers for L5B and L6B regulators on Lahaina
dt-bindings: regulator: add rpmh-regulator bindings
dt-bindings: regulator: add refgen regulator bindings
ARM: dts: msm: Add SD card entries for Lahaina
ARM: dts: msm: Add bluetooth power and slimbus slave node
ARM: dts: msm: Add regmap and clocks for interconnects on Lahaina
ARM: dts: msm: Add swr dmic nodes on Lahaina
bindings: Documentation: Update swr mic device tree documentation
bindings: Documentation: Add swr mic device tree documentation
dt-bindings: add documentation for leds-qti-flash
bindings: power: supply: add QTI battery charger
ARM: dts: msm: Do not bypass SMMU for ufshc
dt-bindings: Add dt binding for Focaltech driver
ARM: dts: msm: fix ipa smp2p node issue
ARM: dts: msm: Add the lahaina gpu dtsi
ARM: dts: msm: update DPC properties for Lahaina
ARM: dts: msm: Change the audio routing sequence
ARM: dts: msm: add documentation qcom,tx-wrapper-cache-max-size
ARM: dts: msm: add qcom,tx-wrapper-cache-max-size property
ARM: dts: msm: Add the offlineable memory sizes for Lahaina
ARM: dts: msm: Update audio device tree overlay for lahaina
ARM: dts: msm: Add turing etm support for Lahaina
ARM: dts: qcom: Remove UFS PHY reset control on Lahaina
ARM: dts: msm: add pinctrl information for Lahaina target
bindings: Documentation: Add wsa883x device tree documentation
dt-bindings: regulator: pm8008-regulator: add OCP interrupt support
ARM: dts: msm: Move apps_rsc before interconnect devices
ARM: dts: msm: Set USB mode as peripheral only on Lahaina
bindings: add audio device tree for lahaina
bindings: Documentation: add QTI audio documentation
ARM: dts: msm: Add USB Uni PHY related device node on Lahaina
ARM: dts: msm: Update and enable the debug cc measure nodes
ARM: dts: msm: Add QTI crypto device-tree node for Lahaina
bindings: Add device-tree bindings for QTI crypto drivers
dt-bindings: input: Add dt bindings for STMicro
ARM: dts: qcom: Add dtsi node entry for Slimbus in lahaina
ARM: dts: msm: use clock driver to vote for IPA code
ARM: dts: msm: Add ACTLR settings for the APPS and GFX SMMUs
dt-bindings: nfc: Add Documentation for I2C NFC devicetree node
ARM: dts: msm: Fix GSI IRQ type warnings on lahaina
dt-bindings: thermal: Add ADC_TM documentation for PMIC7
ARM: dts: msm: Add TSENS node support for lahaina
ARM: dts: msm: Add jtagmm device node for lahaina
ARM: dts: msm: Add initial device tree for Lahaina QRD Module
ARM: dts: msm: update port number to hex format
ARM: dts: msm: Add qseecom node for Lahaina
ARM: dts: msm: Enable s1 in fastmap for QUPv3 drivers on lahaina
ARM: dts: msm: Add 2-wire UART node for lahaina
ARM: dts: msm: Add cpufreq-hw node for Lahaina
dt-bindings: ufs: Add compitable string for V4 UFS PHY on Lahaina
ARM: dts: msm: add reset support for UFS on Lahaina
ARM: dts: msm: Add pshold to Lahaina
dt-bindings: qti-tri-led: Update reg definition
dt-bindings: pwm-qti-lpg: Update reg definition
ARM: dts: qcom: add dt entry needed for avb
dt-bindings: android: add entries for android
ARM: dts: msm: Enable QRNG driver for lahaina
dt-bindings: cpufreq: Add msm-cpufreq bindings snapshot
dt-bindings: Add USB audio QMI driver bindings
ARM: dts: msm: Add SPS driver node for Lahaina
ARM: dts: msm: Add etm save/restore for Lahaina
dt-bindings: rng: Add DT binding entry for msm-rng
ARM: dts: msm: Disable usb1 on Lahaina RUMI
ARM: dts: msm: Add EUD node for Lahaina
ARM: dts: msm: Add device tree overlay support for Lahaina
ARM: dts: msm: add documentation tx-napi
dt-bindings: slim-msm-ngd: Add dt bindings for slimbus driver
dt-bindings: nfc: Add Documentation for I3C NFC devicetree node
ARM: dts: msm: Add coresight device tree for Lahaina
dt-bindings: devfreq: add support for L3 voting in devfreq_icc
dt-bindings: devfreq: add support for shared core-dev tables
dt-bindings: iio: adc: Add PMIC7 VADC bindings
ARM: dts: msm: add volume up gpio-keys device for Lahaina boards
ARM: dts: msm: add PMK8350 PON_PBS and PON_HLOS devices
dt-bindings: input: add qpnp-power-on bindings
ARM: dts: msm: add SPMI debug bus for Lahaina boards
ARM: dts: msm: add PMIC devices for Lahaina
ARM: dts: msm: Specify clock-output-names for sleep_clk on Lahaina
ARM: dts: qcom: Add QUP ICC Core2x path IDs for QUPv3 node
ARM: dts: msm: add initial PCIe nodes for lahaina
dt-bindings: arm: msm: remove msm-bus and add ICC for PCIe
dt-bindings: arm: msm: add initial devicetree documenation for MSI
dt-bindings: arm: msm: add initial devicetree documentation for PCIe
dt-bindings: clocks: Add debugcc clock bindings for Lahaina
dt-bindings: pinctrl: qcom-pmic-gpio: add PMR735A and PMR735B bindings
dt-bindings: rtc: rtc-pm8xxx: Add binding documentation for pmk8350 rtc
ARM: dts: msm: add SPMI PMIC arbiter device for Lahaina
ARM: dts: msm: Add L3 devfreq devices for Lahaina
ARM: dts: msm: Update SIDs for test devices
dt-bindings: cpufreq: Add cpufreq firmware bindings
ARM: dts: msm: add spss_utils to lahaina
ARM: dts: msm: enable ipa smp2p
ARM: dts: msm: Update the smem size for Lahaina
ARM: dts: msm: Add limit rate on G4 for Lahaina rumi
ARM: dts: msm: Add ufs bus voting details for Lahaina
ARM: dts: qcom: Add spcom to support SPU on lahaina
ARM: dts: msm: Add ion heap for Secure Processor on lahaina
ARM: dts: msm: Add interconnect l3 epss devices for Lahaina
ARM: dts: msm: Configure SMMU in bypass mode for Lahaina RUMI
ARM: dts: msm: Add LLCC and DDR devfreq devices for Lahaina
dt-bindings: interconnect: add EPSS L3 bindings
ARM: dts: msm: Add QUPv3 SE and GPI DT node for lahaina
dt-bindings: Add dt bindings for jtagv8 driver
dt-bindings: qti-tri-led: Add bindings
dt-bindings: pwm-qti-lpg: Add bindings
dt-bindings: Add snapshot of thermal devicetree bindings
ARM: dts: msm: enable rmtfs for Lahaina
dt-bindings: Add device-tree bindings for EUD driver
ARM: dts: msm: Update Lahaina's memory map to V3
dt-bindings: devfreq: add support for memory latency QoS voting
dt-bindings: devfreq: add support for new memlat design
dt-bindings: devfreq: add support for different ddr types
dt-bindings: kgsl: Add device tree bindings for the KGSL GPU driver
dt-bindings: perf: Add DT bindings for LLCC_PMU_VER2 driver
dt-bindings: perf: Add DT bindings for QCOM LLCC PMU driver
dt-bindings: devfreq: Add DT bindings to support OPP BW values
dt-bindings: Add DT bindings to support compute bound logic
ARM: dts: msm: Add vdd_cx-supply node to gcc on Lahaina
dt-bindings: clocks: Update gcc clock bindings for Lahaina
ARM: dts: msm: Add vdd_mx-supply node to gpu cc on Lahaina
dt-bindings: clocks: Update gpucc clock bindings for Lahaina
bindings: Add device-tree bindings for qseecom driver
ARM: dts: msm: Add tz_log node for Lahaina
bindings: Add device-tree bindings for tz_log driver
dt-bindings: devfreq: Add DT bindings to add a stall cycle count event
dt-bindings: Add DT bindings for specifying the count factor
dt-bindings: devfreq: Make the freq-table property optional
dt-bindings: devfreq: Add DT bindings to configure byte MID match
ARM: dts: msm: Add smcinvoke node for Lahaina
bindings: Add device-tree bindings for smcinvoke driver
ARM: dts: msm: add lan-rx-napi property
ARM: dts: msm: add PIL spss node to lahaina
dt-bindings: Add camera devicetree bindings for lahaina
ARM: dts: msm: remove SPI config property
ARM: dts: msm: Update USB interrupt trigger types on Lahaina
ARM: dts: msm: Enable dcc on lahaina
ARM: dts: msm: update clock_rpmh device node for Lahaina
dt-bindings: clock: Add rpmh clock bindings for Lahaina
dt-bindings: add devicetree binding for fsa4480
ARM: dts: msm: Add USB PHY devices and related resources on Lahaina
bindings: add support for qcom,ucsi-glink
dt-bindings: devfreq: Add dt-bindings for BWMON HW version 5
dt-bindings: devfreq: Add DT bindings for ARM memlat driver
dt-bindings: devfreq: Add support for BWMON HW version 4
dt-bindings: devfreq: Add dt-bindings for BWMON HW version 3
dt-bindings: devfreq: Add the dt bindings for clock prepare
dt-bindings: devfreq: Add DT bindings for devfreq_simple device
dt-bindings: devfreq: Add dt-bindings for BWMON HW version 2
dt-bindings: devfreq: Add DT bindings for bimc bwmon driver
dt-bindings: devfreq: Add DT bindings for devfreq_icc device
ARM: dts: msm: IPA msm bus dtsi update for Lahaina
dt-bindings: i3c-master-qcom-geni: Add DT bindings for I3C GENI driver
ARM: dts: msm: Update and enable clk-aop clks on Lahaina
ARM: dts: qcom: add virt_clk interconnect provider
dt-bindings: interconnect: Add clk_virt documentation on Lahaina
ARM: dts: msm: Add USB BAM device node on Lahaina
ARM: dts: msm: Add support for modem PIL
ARM: dts: msm: Add SCM node
dt-bindings: regulator: add proxy consumer bindings
dt-bindings: pmic-glink: add qcom,pmic-glink-channel property
ARM: dts: msm: Add GDSC regulator references for Lahaina's SMMUs
bindings: add support for qcom,pmic-glink
ARM: dts: msm: Add SSC based sensors with SLPI PIL on Lahaina
ARM: dts: msm: Add modem smp2p for Lahaina
ARM: dts: msm: Document kona device binding
ARM: dts: msm: Add ARM PMU node for Lahaina
dt-bindings: spi-msm-geni: Add DT bindings for SPI GENI driver
ARM: dts: msm: Add CVP device tree for Lahaina
ARM: dts: msm: add reset control support for UFS PHY on Lahaina
ARM: dts: msm: Add embedded UFS device reset GPIO on Lahaina
dt-bindings: nvmem: add bindings for QTI SDAM devices
dt-bindings: soc: qcom: add bindings for QTI PBS devices
dt-bindings: platform: msm: add bindings for qpnp-revid devices
dt-bindings: spmi: spmi-pmic-arb-debug: add clock management support
dt-bindings: spmi: add SPMI PMIC arbiter debug bus bindings
dt-bindings: mfd: add qcom-i2c-pmic bindings
ARM: dts: msm: Add Lahaina video configuration
dt-bindings: pinctrl: qcom-pmic-gpio: add PM*8350* bindings
dt-bindings: mfd: qcom,spmi-pmic: add documentation for qcom,can-sleep
dt-bindings: gpi: Add DT bindings for GPI dmaengine driver
ARM: dts: msm: Update and enable graphics clock controller on Lahaina
dt-bindings: clocks: Add gpu cc clock controller bindings for Lahaina
ARM: dts: msm: Add IPA dtsi entry for Lahaina
dt-bindings: i2c-msm-geni: Add DT bindings for I2C GENI driver
ARM: dts: msm: Add QUPV3 SE dt node for uart on Lahaina
dt-bindings: Add device-tree bindings for slimbus slave driver
dt-bindings: usb: Document USB qcom,usb-charger property
ARM: dts: msm: add dt nodes for adsp & cdsp PIL for Lahaina
ARM: dts: msm: change lan_rx_napi to lan-rx-napi
bindings: usb_bam: Add USB BAM driver related documentation
ARM: dts: msm: Update bus entries in pil-video node
dt-bindings: media: Add video driver bindings for Lahaina
ARM: dts: msm: Update USB device nodes on Lahaina
dt-bindings: usb: Add bindings for MSM SSUSB
dt-bindings: usb: Document dwc3 xhci-imod-value property
ARM: dts: msm: add dt node for video
ARM: dts: msm: Add camera pinctrl info for Lahaina
bindings: Add USB PHY drivers related documentation
ARM: dts: msm: Add glink entries for Lahaina
ARM: dts: msm: Update and enable the cam cc node on Lahaina
dt-bindings: clocks: Add cam cc clock controller bindings for Lahaina
dt-bindings: Add snapshot for 5.4-rc2
ARM: dts: msm: add documentation lan_rx_napi
ARM: dts: msm: Enable the secure carveout heap on Lahaina
ARM: dts: msm: Unstub the DISP_CC node for Lahaina
dt-bindings: clk: Add DISP_CC clock driver bindings for Lahaina
ARM: dts: msm: Unstub the VIDEO_CC node for Lahaina
dt-bindings: clk: Add VIDEO_CC clock driver bindings for Lahaina
ARM: dts: msm: add initial device tree for Lahaina low power modes
ARM: dts: msm: Add glink entry for spss on Lahaina
ARM: dts: msm: Add shmbridge node for Lahaina
bindings: Add device-tree bindings for qtee_shmbridge driver
dt-bindings: Add spcom documentation
dt-bindings: Add spss_utils documentation
ARM: dts: msm: add wakeup parent for Lahaina
dt-bindings: arm: snapshot of psci bindings
dt-bindings: Introduce soc sleep stats bindings for QTI SoCs
dt-bindings: add device bindings for DDR stats node
dt-bindings: msm: add PM drivers device bindings
ARM: dts: qcom: add USB GDSC supplies for Lahaina
ARM: dts: qcom: switch PM8350 LDO 7 to RPMh control for Lahaina
ARM: dts: qcom: add GDSC devices for Lahaina
ARM: dts: qcom: add refgen regulator device for Lahaina
dt-bindings: regulator: add refgen regulator bindings
ARM: dts: qcom: switch to RPMh controlled PMIC regulators for Lahaina
ARM: dts: qcom: add PMIC PMR735A regulator devices for Lahaina
ARM: dts: msm: Add bcm voter devices for lahaina
dt-bindings: interconnect: Update QTI SDM845 DT bindings
dt-bindings: regulator: add rpmh-regulator bindings
ARM: dts: qcom: update PMIC regulator voltage limits for Lahaina
dt-bindings: of: irq: document properties for wakeup interrupt parent
dt-bindings: pdc: Add SPI config register
ARM: dts: msm: add capacity and DPC properties for Lahaina
ARM: dts: msm: Add WDT node for Lahaina
ARM: dts: msm: Update and enable the clock_gcc node on Lahaina
dt-bindings: clocks: add gcc clock controller bindings for Lahaina
dt-bindings: dma: sps: Add dt binding for SPS driver
dt-bindings: regulator: add PMIC PM8008 regulator bindings
ARM: dts: msm: remove uncessary node from IPA nodes for Lahaina SoC
ARM: dts: msm: Correct the UFS PHY address space for Lahaina
ARM: dts: msm: Use dt-bindings header for ION on Lahaina
ARM: dts: msm: Add smp2p sleepstate node for Lahaina
ARM: dts: msm: Add AOP QMP nodes for Lahaina
ARM: dts: msm: Update the timer clock frequence as per RUMI E3.0
dt-bindings: arm: Add CSR/TPDM/TPDA/TGU/Remote ETM support
ARM: dts: msm: add fastrpc and cdsp device nodes for lahaina
dt-bindings: Add device-tree bindings for Watchdog driver
ARM: dts: msm: add RSC device bindings for lahaina
ARM: dts: msm: add PDC device bindings for Lahaina
dt-bindings: Add documentation for the mem-offline driver
ARM: dts: msm: Add core hang detection to dt
bindings: Add qcom,msm-hang-detect schema
dt-bindings: arm: coresight: add trace unit power property
dt-bindings: Add dt bindings for memory dump
dt-bindings: Add dt bindings for dcc
dt-bindings: Add device-tree bindings for BT power driver
dt-bindings: regulator: gdsc-regulator: add property for register retention
dt-bindings: clk: gdsc-regulator: add parent supply property
dt-bindings: regulator: add gdsc-regulator bindings
dt-bindings: clock: add rpmh clock bindings for Kona
dt-bindings: clk: add AOP clock controller bindings
dt-bindings: qdsp: device-tree documentation for fastrpc and CDSP loader
dt-bindings: Add device-tree bindings for rtc6226 driver
ARM: dts: msm: Add IPA node for Lahaina SoC
bindings: serial: Binding for serial UART driver
bindings: qcom-geni-se: Common GENI driver
dt-bindings: Add snapshot for 5.3-rc4
dt-bindings: qdsp: Device tree documentation for sensors ssc
ARM: dts: msm: Add initial ION heaps for Lahaina
ARM: dts: msm: Make the CDSP secure carveout mappable on Lahaina
ARM: dts: msm: add msm_rtb tracing
bindings: Add qcom,msm-rtb schema
ARM: dts: msm: Add USB device nodes for Lahaina
ARM: dts: msm: Add HWSPINLOCK, SMEM and SMP2P for Lahaina
ARM: dts: msm: Disable the coherent KGSL IOMMU test device
ARM: dts: msm: Fix major and minor versions for Lahaina boards
dt-bindings: net: qrtr: Add FIFO transport bindings
dt-bindings: arm: msm: Add sleepstate-smp2p bindings
dt-bindings: arm: msm: Introduce qsee_ipc_irq_bridge bindings
dt-bindings: arm: msm: Introduce qcom,qsee_irq bindings
dt-bindings: soc: qcom: Introduce Glink Pkt bindings
dt-bindings: soc: qcom: Introduce Glink Probe bindings
ARM: dts: msm: Add device-tree entry for IMEM
ARM: dts: msm: Add support for SCM PAS
dt-bindings: Add device-tree bindings for IMEM
bindings: Add device-tree bindings for secure PIL driver
dt-bindings: Introduce QMP debugfs client bindings
dt-bindings: mailbox: Introduce MSM_QMP bindings
dt-bindings: kryo-edac: add kryo edac bindings
ARM: dts: msm: Add edac node for Lahaina SoC
ARM: dts: msm: Enable the graphics SMMU on Lahaina
dt-bindings: Add device-tree bindings for CNSS2 driver
ARM: dts: msm: Add IPCC test nodes for end to end verification
ARM: dts: msm: Add IPCC node for Lahaina
dt-bindings: Add device-tree bindings for IPCC driver
ARM: dts: msm: Make LLCC node compatible with "qcom,lahaina-llcc"
dt-bindings: LLCC: Add "qcom,lahaina-llcc" compatible property
dt-bindings: Add device-tree bindings for the ION memory manager
ARM: dts: msm: Add the SMMU devices for Lahaina
ARM: dts: msm: Add the secure buffer device for Lahaina
dt-bindings: Merge all IOMMU documentation from msm-4.19 to msm-lahaina
ARM: dts: msm: Add device-tree node for LLCC driver
dt-bindings: LLCC: Add "qcom,llcc-v2" compatible property
ARM: dts: msm: add ufs device support for Lahaina
ARM: dts: msm: add stub interconnect devices for Lahaina
bindings: usb: Add bindings for USB PHY on QTI emulation platform
ARM: dts: msm: Add SCM node for Lahaina SoC
bindings: Add device-tree bindings for SCM driver
ARM: dts: msm: Add memory carveouts as per Lahaina v2 memory map
dt-bindings: interconnect: add interconnect bindings
dt-bindings: Add snapshot from tmp-f686d9f
ARM: dts: msm: Add pinctrl node for TLMM on Lahaina SoC
bindings: pinctrl: Add device-tree bindings for Lahaina pinctrl driver
ARM: dts: msm: add stub clock devices for Lahaina
dt-bindings: clocks: add dummycc bindings
bindings: Add snapshot of bindings with GPL-2.0 or BSD-2-Clause license
ARM: dts: msm: add stub regulator devices for Lahaina
dt-bindings: regulator: add stub regulator bindings
ARM: dts: msm: Add initial device tree for Lahaina
dt-bindings: msm: Add compatible strings for Lahaina
dt-bindings: Snapshot of msm device tree binding document
ARM: dts: vendor: Add an initial Makefile to the vendor
dt-bindings: Add devicetree bindings to devicetree project
Initial empty repository
Change-Id: Icb722bcaa651702f1843582ae7f1bd9807681018
2020-05-08 12:56:50 -07:00
Venkata Narendra Kumar Gutta
b0e5152a74
dt-bindings: Add devicetree bindings to devicetree project
...
Add devicetree bindings snapshot to the devicetree project.
This snapshot is taken as of the
'commit 5fba1b18cfc72e264e5f3ce49020ed322aa6ac9f ("Merge 5.6-rc3
into android-mainline")' of the kernel project.
Change-Id: Ia087ab2b7d4a2616ea446a69683a8b5b821d0448
2020-05-07 20:43:53 -07:00
Subbaraman Narayanamurthy
8ef80559d3
dt-bindings: qpnp-amoled: add support to configure single phase for IBB
...
On certain PMICs like PM8350B, IBB can be configured in single or
dual or auto phase based on the panel configuration. Though dual
or auto phase is mostly used, forced single phase configuration
is needed for some hardware. Add support for it.
Change-Id: I49206d1a68392362a32fd4a193f0891ccae3078d
2020-05-06 16:55:51 -07:00
Kavya Nunna
5b56df5c20
dt-bindings: regulator: Add snapshot of rpm-smd-regulator doc
...
This is snapshot of the rpm-smd-regulator.txt as of msm-4.14
'commit 637a26bd203d34ce("regulator: rpm-smd: Add support for
set_load function.")'.
Change-Id: Ibcd863e65238d1ff10aee235b570000e698321b6
2020-04-29 02:07:34 -07:00
Shyam Kumar Thella
cfde88c84d
dt-bindings: qpnp-amoled: Update voltage ranges for PM8150A/PM8350B
...
Modify the voltage ranges for PM8150A AMOLED regulator bindings based
on hardware documentation. Also add voltage ranges for PM8350B.
Change-Id: Ia3caa678706ba36df3499bfc96b65cd6d3c75a36
2020-04-09 16:10:02 +05:30
Jishnu Prakash
e06193f460
dt-bindings: qpnp-lcdb-regulator: Add LCDB regulator documentation
...
Add documentation for QPNP LCDB regulator module. The driver
helps with controlling display bias voltage rails for LCD panels.
Change-Id: I526ae7553f5631e75b79114b386d10c1053e5453
2020-03-23 17:55:10 +05:30
qctecmdr
e4e59c5761
Merge "dt-bindings: Add snapshot of QPNP AMOLED regulator bindings"
2020-02-03 14:44:47 -08:00
qctecmdr
39118d2eba
Merge "dt-bindings: regulator: add rpmh-regulator bindings"
2020-01-30 10:09:44 -08:00
Shyam Kumar Thella
51087911ef
dt-bindings: Add snapshot of QPNP AMOLED regulator bindings
...
Add bindings for QPNP AMOLED regulator which is used to configure
triple power supply for amoled displays.
Change-Id: I28b5dcbfa288884b97260bdc5204bce455f97ce1
2020-01-27 15:14:59 +05:30
David Collins
c7ebd0286c
dt-bindings: regulator: add rpmh-regulator bindings
...
Add rpmh-regulator device bindings for PMIC regulator management
via the RPMh hardware block on Qualcomm Technologies, Inc. SoCs.
This is a snapshot from msm-4.19
commit e3299424fb89 ("dt-bindings: regulator: add rpmh-regulator
bindings").
Change-Id: Iaef882a97a31cbb0c592f4ac5d9115a8b389f387
2020-01-21 12:40:49 -08:00
David Collins
03d615fb24
dt-bindings: regulator: add refgen regulator bindings
...
Some Qualcomm Technologies, Inc. SoCs such as SDM845 utilize
reference bias generators for various internal PHY blocks.
These are called REFGENs. Add binding documentation for
REFGEN devices.
This is a snapshot from msm-4.19
commit e5cf0a03c6aa ("dt-bindings: regulator: add refgen
regulator bindings").
Change-Id: I9efbea760ba0b07544549d0e28692e386d0c4350
2020-01-21 12:40:49 -08:00
Kiran Gunda
597a7461b6
dt-bindings: regulator: pm8008-regulator: add OCP interrupt support
...
Add PM8008 PMIC LDO regulator over current protection (OCP) interrupt
support and notify the consumers of the corresponding LDO when the
OCP event occurred.
Change-Id: I79f41a9beb25b6fd4b7f90b2ce60a705ef0500b0
2020-01-08 16:39:56 -08:00
David Collins
afaee4210b
dt-bindings: regulator: add proxy consumer bindings
...
Add bindings for regulator proxy consumers which can be used to
enforce minimum voltage, current, and enable state of regulators
when a board is booting up.
Change-Id: If51da56b7c8f685d0c8a93d514964d2c924381ce
2019-11-08 16:47:49 -08:00
Raghavendra Rao Ananta
e4b1dcc77e
dt-bindings: Add snapshot for 5.4-rc2
...
Add the device-tree bindings' snapshot from tmp-abe0ec5a8133 for
5.4-rc2.
Change-Id: I346809db756dd18a509ce440499d98a7fefecd16
2019-10-16 10:18:01 -07:00
qctecmdr
d635065a88
Merge "ARM: dts: qcom: add refgen regulator device for Lahaina"
2019-10-03 16:09:28 -07:00
qctecmdr
d2c3d11eca
Merge "dt-bindings: regulator: add PMIC PM8008 regulator bindings"
2019-10-03 15:30:18 -07:00
David Collins
e06afd1c00
dt-bindings: regulator: add refgen regulator bindings
...
Some Qualcomm Technologies, Inc. SoCs such as SDM845 utilize
reference bias generators for various internal PHY blocks.
These are called REFGENs. Add binding documentation for
REFGEN devices.
This is a snapshot from msm-4.19
commit e5cf0a03c6aa ("dt-bindings: regulator: add refgen
regulator bindings").
Change-Id: I83c37e3a1fb33bd552849f7cf20d602a901a40d2
2019-10-02 16:41:36 -07:00
David Collins
9dbefce868
dt-bindings: regulator: add rpmh-regulator bindings
...
Add rpmh-regulator device bindings for PMIC regulator management
via the RPMh hardware block on Qualcomm Technologies, Inc. SoCs.
This is a snapshot from msm-4.19
commit e3299424fb89 ("dt-bindings: regulator: add rpmh-regulator
bindings").
Change-Id: Ic9cd30f9da854b663e73f06d516a76f79ca8ae94
2019-10-01 17:56:52 -07:00
David Collins
d8db64f99a
dt-bindings: regulator: add PMIC PM8008 regulator bindings
...
Add PMIC PM8008 regulator device bindings. PM8008 chips contain
7 LDO regulators along with a top-level chip sleep feature.
Change-Id: If36c21dbf382b2bc460e712b0098f67d569004ca
2019-09-24 11:10:46 -07:00
David Collins
019ed7ab7c
dt-bindings: regulator: gdsc-regulator: add property for register retention
...
Add the description for a new property, qcom,retain-regs, which
can be used to specify that retention registers should be
configured to maintain their state after a GDSC is disabled
and re-enabled.
Change-Id: Ic3649de0804d47117bddff72f3713c1ab24e33b2
2019-08-29 12:08:27 -07:00
David Collins
ab00083a1c
dt-bindings: clk: gdsc-regulator: add parent supply property
...
Add a property to specify the parent supply voltage regulator
which must be enabled during GDSC register configuration.
Change-Id: I62e3f869f8b33faca8838151876420bb08fda601
2019-08-29 12:06:06 -07:00
David Collins
5facba964f
dt-bindings: regulator: add gdsc-regulator bindings
...
Globally distributed switch controllers (GDSCs) are used to
switch the power supplied to a particular hardware block within
a Qualcomm Technologies, Inc. SoC on and off. Add gdsc-regulator
device bindings.
Change-Id: Iae47c4fe22c19060d120ef51249b15b20160e0fe
2019-08-29 12:05:56 -07:00
Raghavendra Rao Ananta
430b7fac16
dt-bindings: Add snapshot for 5.3-rc4
...
Add the device-tree bindings' snapshot from tmp-9855ec2fd422 for
5.3-rc4.
Change-Id: I25b0ac9b29c0347f557b87094ede86370a89a0f2
2019-08-22 23:08:38 -07:00
David Collins
375a0fcdc2
dt-bindings: regulator: add stub regulator bindings
...
Add stub-regulator device bindings. These devices can be used to
simulate any particular voltage regulator.
Change-Id: Icb701dcc358b63490b88698d2710e4b19d9448bd
2019-06-07 14:42:17 -07:00
Murali Nalajala
719cc9aa79
dt-bindings: Add devicetree bindings to devicetree project
...
Add devicetree bindings snapshot to the devicetree project
Change-Id: I20b46d194bd3b107ddcb3e35283e6dafa27adec1
2019-05-31 16:45:27 -07:00
