Fix the issue with retrieving BluetoothA2dp and BluetoothLe
instances access.
In 'Module::connectExternalDevice', always call
'populateConnectedDevicePort' to allow the module implementation
to cancel device connection.
Move frame count calculation into Utils.
Clean up includes and 'using' directives.
Bug: 302132812
Test: atest VtsHalAudioCoreTargetTest
Change-Id: I22f65b8bcdcdd9bcd67a8290520eb4a465d4c720
The latency figure depends on the module implementation.
Instead of using a hardcoded value, each module should be
able to specify its own value. This value is then used
for calculating the minimum buffer size.
Set the nominal latency of the primary (CF) module to a high
value since the virtual device implementation fails CTS tests
if it attempts to pretend that it provides low latency.
Bug: 302132812
Test: atest CtsMediaAudioTestCases --test-filter=".*AudioTrackTest.*"
Test: atest CtsMediaAudioTestCases --test-filter=".*AudioRecordTest.*"
Change-Id: I8ce9f230378eea787c9b3c7ce3660c1e4e7bc895
** Partial upstream of ag/24854732. Only the interface part is
** included.
This should enable the sound dose gts on cuttlefish devices. The sound
dose HAL uses the internal MelProcessor to compute the MELs which are
reported to the framework.
Test: atest GtsAudioTestCases:SoundDoseTest
Bug: 301527435
Change-Id: Ifc505a0171bc8b4d3f5cf65d950fa5c0f812087f
Merged-In: Ifc505a0171bc8b4d3f5cf65d950fa5c0f812087f
For external (non-attached) device ports that have dynamic
profiles, 'connectedProfiles' must be provided. They are
used when 'ModuleDebug.simulateDeviceConnections' is enabled.
Bug: 205884982
Test: atest VtsHalAudioCoreTargetTest
(cherry picked from commit a29393db39)
Change-Id: I69707d610c34f8f1eae9ef81768b76c40e985c0f
Added a virtual method Module::getMicrophoneInfos
so that vendor implementations can provide actual
data about device microphones. This information
is not part of the APM config file.
Bug: 205884982
Test: atest VtsHalAudioCoreTargetTestTest
(cherry picked from commit dc9d1a4b42)
Change-Id: I3ea9ba8da79fd29f8d69c5a575a57851d73df7b8
The default implementation now loads the HAL configuration
from the legacy XML configuration file which was previously
consumed by the framework directly.
Note that errors in the config file will lead to crash
of the XML parser, pointing out to the source of the problem.
IMPORTANT NOTES:
- Never use untested legacy config files with production
devices.
- Make sure that all possible configurations (for example,
BT offload on/off) are tested.
Bug: 205884982
Test: atest VtsHalAudioCoreTargetTest
(cherry picked from commit 00a7307862)
Change-Id: Id1002cb065e7cc19bdd520aca15b3fe5d39e5853
For external (non-attached) device ports that have dynamic
profiles, 'connectedProfiles' must be provided. They are
used when 'ModuleDebug.simulateDeviceConnections' is enabled.
Bug: 205884982
Test: atest VtsHalAudioCoreTargetTest
Change-Id: Ic82e47abc50e2958ed93f5d4d18082b569ecb67b
Added a virtual method Module::getMicrophoneInfos
so that vendor implementations can provide actual
data about device microphones. This information
is not part of the APM config file.
Bug: 205884982
Test: atest VtsHalAudioCoreTargetTestTest
Change-Id: I4b650ae221ba866421bbf8500ad8c17f04bc4aa7
The default implementation now loads the HAL configuration
from the legacy XML configuration file which was previously
consumed by the framework directly.
Note that errors in the config file will lead to crash
of the XML parser, pointing out to the source of the problem.
IMPORTANT NOTES:
- Never use untested legacy config files with production
devices.
- Make sure that all possible configurations (for example,
BT offload on/off) are tested.
Bug: 205884982
Test: atest VtsHalAudioCoreTargetTest
Change-Id: I01e4cd77a284d7df64ecb0c0b21cb16abfa0f6c5
Some device ports are connected via ADSP which takes care
of the actual audio configuration (format, channels, SR),
for example the built-in speaker and mic ports, as well
as some external devices like analog headsets.
In the legacy implementation, such device ports did not have
any profiles specified. Allow the same behavior in the AIDL
implementation. To ensure correctness, device ports with no
profiles must be routable to mix ports that have profiles
specified. This requirement is fulfilled in legacy configs.
Bug: 266124463
Test: atest VtsHalAudioCoreTargetTest
Test: atest audiosystem_tests audiorouting_tests
Test: atest CtsMediaAudioTestCases
Change-Id: Iaccd1e8ef2a5af9a5f8bae453905d01c6b7fdc28
This should enable the sound dose gts on cuttlefish devices. The sound
dose HAL uses the internal MelProcessor to compute the MELs which are
reported to the framework.
Test: atest GtsAudioTestCases:SoundDoseTest
Bug: 301527435
Change-Id: Ifc505a0171bc8b4d3f5cf65d950fa5c0f812087f
Replace the incorrect logic which was considering each
port individually with the correct logic which considers
a connection of a mix port to device ports.
Bug: 302573756
Test: atest VtsHalAudioCoreTargetTest
Change-Id: I7df6e32315945897d88923ea4d9744e590e85dfd
The code for updating the existing patch did not modify
the patch stored in the module's list of patches.
Added a test which switches the patch to another port
config and validates that 'Module.getAudioPatches' returns
the updated patch.
Bug: 302573756
Test: atest VtsHalAudioCoreTargetTest
Change-Id: I0e3412b9387cd451436a48af116dc5a940d868cf
When there are no device ports supporting MMAP,
Module::getMmapPolicyInfos have to return 'Policy::NEVER'
so that the AAudio code does not attempt to use
the AAudio service. This aligns with the use of sysprops
by the HIDL implementation.
Update AudioCoreModule#GetMmapPolicyInfos test to use
the same logic for determining MMAP support as the framework
uses.
This makes CtsNativeMediaAAudioTest cases passing with
the AIDL HAL on Cuttlefish.
Bug: 302049825
Test: atest VtsHalAudioCoreTargetTest
Test: atest CtsNativeMediaAAudioTest [w/AIDL enabled on CF]
Change-Id: Ie58c408f6f648a8a03b6a5d92118b90061389c50
A mix port can be patched to multiple connected device ports. Thus, when
disconnecting an external device and removing the connected port, the
profiles of the mix port can only be cleared iff there are no more
connected device ports patched to it, and it did not have profiles prior to
connection of the first device.
Enhanced VTS tests to catch this problem in the HAL implementations. Also,
ensure that audio ports and audio routes do not change after the test
finishes. This ensures that tests can't affect each other.
Bug: 298175108
Test: atest audiosystem_tests
Test: atest VtsHalAudioCoreTargetTest
Change-Id: Ia666b874958fb260513fc2b8cd20a823953ec679
External device ports might not have dynamic profiles, for example,
ports for BT devices. Properly handle this case in the default
implementation.
Bug: 264712385
Test: atest VtsHalAudioCoreTargetTest
Test: atest audiosystem_tests
Change-Id: I8d4bcbf6ccf2ba05436e68e3ba94567fc7610eb7
Since the client may end up never retrieving the interface
instance for sending it over Binder, postpone setting
of the scheduler policy to until that very moment.
Rename 'ChildInterface::getPtr' to 'getInstance' for clarity.
Bug: 264712385
Test: atest VtsHalAudioCoreTargetTest
Change-Id: I31f9dd832c7f85f9632d1d389a8b1063d237d4c1
* changes:
audio: Move StreamContext ownership out from StreamCommonImpl
audio: Use ChildInterface in StreamCommonImpl
audio: Update StreamAlsa and alsa utils for built-in devices
audio: Simplify and extend alsa::Mixer
Upcoming implementations of the streams of the primary module
will need to change the underlying stream type depending on
the current connected device. The stream context must persist,
thus its life time must be bound to the IStreamIn/Out implementation.
Move the StreamContext instance under ownership of StreamIn/Out.
Add StreamCommonImpl::onClose so that the owner of the context
may know when it is safe to reset it.
Re-arrange the order of the arguments when creating a stream
so that the context always comes first.
Bug: 264712385
Test: atest VtsHalAudioCoreTargetTest
Change-Id: Iaf13d4bc3a53cbfc27264d3abd1f6c417ece3941
When a vendor HAL reuses libaudioserviceexampleimpl,
a subclass of Module cannot change Configuration.
This change adds virtual method Module::initializeConfig(),
then a vendor HAL can override it to load custom Configuration.
Test: atest VtsHalAudioCoreTargetTest
Change-Id: I63fa8d70f3c4e13c8938070ee5431ebefd36bb58
Make 'Module' more abstract by moving stream creation
methods to more concrete 'ModulePrimary' and 'ModuleStub'.
'ModulePrimary' is now closer to the CF primary module:
it was stripped off USB devices from its configuration,
these got moved to 'ModuleUsb', and got rid of BT A2DP
and LE interfaces, these will be on 'ModuleBluetooth'.
Note that 'ModulePrimary' still uses stub streams, this
will be changed in subsequent patches.
'ModuleStub' is what 'Module' used to be, just a module
for improving test coverage. It includes simulation of
offload streams and dummy BT objects.
Bug: 264712385
Test: atest VtsHalAudioCoreTargetTest
Change-Id: I5e4da0c32c00d65688f2eda78b2c79594e4e4671
Since specializations of the 'Module' class likely need
to provide their own specializations for streams, provide
virtual methods for them.
Bug: 282568751
Test: atest VtsHalAudioCoreTargetTest
Change-Id: Iddb1bff9f11bc867aba61897ea2f8b9bc3c27544
Plumb propagation of errors reported by the implementations
of DriverInterface::setConnectedDevices up to the Module.
This allows returning the reported errors from the corresponding
IModule interface methods. Implement handling of errors
from connection state update by the Module implementation.
When updating streams about the connection status
ensure that the list of connected devices is not empty.
Also, add an extra check to AudioStreamIn#ActiveMicrophones
to validate the size of the returned active microphones
list.
Bug: 282568751
Test: atest VtsHalAudioCoreTargetTest
Change-Id: I62a422d95c37a672fce4ad221bea435cc7b4ebfa
Vendor implementations may need to see the value of flags
and the I/O handle of the mix port used to open the stream.
Bug: 282568751
Test: atest VtsHalAudioCoreTargetTest
Change-Id: If1f346793f3b3a725bc19358909f5b461cb159c1
Clarify what should happen to mix port profiles after
connection of an external device. Add a test to verify
this behavior.
Also, add an XML file for the test runner for
VtsHalAudioCoreTargetTest.
Bug: 273252382
Test: atest VtsHalAudioCoreTargetTest
Change-Id: I3381dd29c5922bf31fa3a8ae6fa273597e8333a1
Merged-In: I3381dd29c5922bf31fa3a8ae6fa273597e8333a1
Add 'isDefaultAudioFormat' to Utils.h.
Print the module type in 'setModuleDebug'.
Align 'suggestDeviceAddressTag' with framework code.
Bug: 273252382
Test: m
Change-Id: I0248d2e866522a63a745d4af6132b7d2b6a01564
Merged-In: I0248d2e866522a63a745d4af6132b7d2b6a01564
These utilities are for types generated from AIDL. Since
the types end up in the 'aidl' namespace (NDK backend), it makes
sense to keep the utilities in the same namespace.
While changing the namespace, I've found numerous useless
includes of 'Utils.h' and removing them, also reorganizing
lists of includes along the way to match the style guide.
Bug: 205884982
Test: m
Test: atest --test-mapping hardware/interfaces/audio/aidl/TEST_MAPPING
Change-Id: Ib23b47092364046f632f9503b92b9baff5b902f5
Similar to IBluetooth and IBluetoothA2dp interfaces,
IBluetoothLe controls the LE profile. This interface
replaces the following string parameter:
"LeAudioSuspended"
Bug: 270731693
Test: atest VtsHalAudioCoreTargetTest
Change-Id: I9df28053cd270fc2d446ba9a8ada4dd6ab761c7b
Merged-In: I9df28053cd270fc2d446ba9a8ada4dd6ab761c7b
