After looking at all the issues reported and logs captured,
these are the firmware logging levels (module-wise)
recommended to be enabled by default.
CRs-Fixed: 2081775
Bug: 63544726
Change-Id: I16a531b651836707963083fdf028874cae738bf2
Signed-off-by: Ecco Park <eccopark@google.com>
The wrong thermal-config was copied for VR mode.
Bug: 37544246
Test: verify that the correct VR thermal config is on-device
Change-Id: I8605336c5fbdac7450036883a68f1f25f111d286
1) Update applies to EVT2.2 and beyond
2) Add & Set the device_max_limit of SKIN-MID-LOW-FLOOR2 to 1497600
3) Raise SKIN-LOW-FLOOR2 set_point to 45 degreeC
4) Add charging current throttling for both normal and vr mode
Bug: 63152009
Bug: 63037732
Test: Boot & check logcat message
Change-Id: I0c10bb36717194aa0f0ac841d1a910eaa634e0c5
One msec is on the edge and sometimes glitches.
Two msec is more stable and matches the FastMixer burst.
Bug: 63934178
Test: "adb shell getprop aaudio.hw_burst_min_usec" should be 2000
Change-Id: I9687f5822d0827032b93f98779f9dd6ef9ca074c
Tested 1/2x, 1x, 2x, and 4x the current readahead buffer and noop and
cfq I/O schedulers for /dev/block/sda, which contains /data. The most
consistent performance boost was seen across all UFS vendors and storage
sizes using cfq and a readahead buffer of 1024.
Note: testing was done on Walleye, not Taimen
Bug: 38000161
Test: Compared 1P app launch times using app-launcher for schedulers
(noop, cfq) and readahead buffer sizes (128,512,1024,2048)
Change-Id: I7551a4110ad025ec7975dd39301f048f0942f585
This will allow AAudio to route audio data through a new service
that uses ALSA MMAP/NOIRQ mode.
Bug: 63002656
Test: reboot, then "adb shell getprop aaudio.mmap_policy" should be 2
Change-Id: Id2f692ac9350e4c308f17d86ee8d5cbb858bb565
Keep the original property also, to make it easier to experiment
with old and new libadm.so
Bug: 63810681
Test: round-trip USB latency unchanged with old or new libadm.so
Change-Id: I3ba8a670f6d8498a5899c352c544cbd63d815169
This reduces the minimum brightness to 0.009 nits from 0.09 nits
(on EVT1 and 2).
Bug: 63834045
Test: manual
Change-Id: I7d76eae6e76de5ed3a125f8f4b42d1bba2f57ac7
RESTRICT_VENDOR_FILES cannot be set to also enforce "path" as some vendor
specific modules related to IMS VT still needs to be installed in system.
Bug: 37330627
Change-Id: Ic94a63b4a53c876553a1c48a7d7a986ac11f790e
Signed-off-by: Thierry Strudel <tstrudel@google.com>
fix rx/tx mute when making call with 3-pole headset and USB dongle
Bug: 63680197
Test: manual audio sanity test
Change-Id: Ie8b3b6d0c5666539a794459e425570f4e5d7d447
This also provides tuning for touch size information.
Test: flash and look at touch size with pointer location enabled
Bug: 62871286
Change-Id: I1dafed6b482a74d9baeac162be1dc831370a5ebc
Bug : 62663757
- Change low persistence(LP) mode brightness from 255 to 159
- If panel version is 2-1, Set LP mode brightness to 255
Change-Id: Ie3754ac9ab11347e4f4edf91a607a17fc6b776fc
Newer revisions of hardware have changed the placement
of the bd_therm thermistor. To allow software to work
on both old and new hardware, we've renamed that thermistor
to bd_therm on the new hardware, which requires a new
set of throttling constraints using that thermistor.
Bug: 63344220
Test: booted old and new hardware, checked configs,
and verified that throttling happened at the right
temps according to the thermistors
Change-Id: I9639142551a8fc1dcbe65559045ae40b2ace5537
- VoIP handset spk analog gain 97->93
- enable handset sidetone
Bug: 62826294
Test: audio sanity test
Change-Id: Ie4a0c92a445589f4345f5a902373d21b0f52a14e
Signed-off-by: David Lin <dtwlin@google.com>
The intervals(dB) by Ringtone/Alarm/Notification are too small to be recognized.
the gap between each step 3dB -> 4.3dB.
Bug: 62826294
Test: notification playback at different volume steps
Change-Id: I02180a71878be65d1d2a976b42ba7c768e903a80
For normal mode, make throttling more aggressive on Taimen,
in line with tuning on our other devices.
For VR mode, add an aggressive throttle just before shutdown.
Bug: 36458508
Bug: 37544246
Test: Booted, checked throttling with adjusted temps
Change-Id: Ia192535ed305cd6e8e1fbae4c53a7b4b7e3e8c23
Remove the cad calibration file and use only factory calibration
file.
Test: Tested on Taimen
BUG=63146009
Change-Id: I3cf1a0084723b925eaa358830f76d48da0841b4e
No change in latency for Taimen
Bug: 62375603
Test: Loopback shows reduction and no glitches on Walleye, no change on Taimen
Change-Id: I6dc85ecdc825462acb4e1cda3227fb4d4f93c56e
