mirror of
https://github.com/Evolution-X-Devices/device_xiaomi_polaris
synced 2026-01-27 14:27:18 +00:00
polaris: Align NFC configs with upstream
* Match all the changes up to LA.UM.7.3.r1-06900-sdm845.0 Change-Id: I9d1ace9fdc102e6cc7f9fee9cd0a10be027dd90e
This commit is contained in:
Bruno Martins
@@ -57,5 +57,5 @@ PRODUCT_PACKAGES += \
|
||||
Tag
|
||||
|
||||
PRODUCT_COPY_FILES += \
|
||||
$(LOCAL_PATH)/nfc/libnfc-brcm.conf:$(TARGET_COPY_OUT_VENDOR)/etc/libnfc-brcm.conf \
|
||||
$(LOCAL_PATH)/nfc/libnfc-nci.conf:$(TARGET_COPY_OUT_VENDOR)/etc/libnfc-nci.conf \
|
||||
$(LOCAL_PATH)/nfc/libnfc-nxp.conf:$(TARGET_COPY_OUT_VENDOR)/etc/libnfc-nxp.conf
|
||||
|
||||
@@ -1,396 +0,0 @@
|
||||
###################### Start of libnfc-brcm.conf #######################
|
||||
|
||||
###############################################################################
|
||||
# Application options
|
||||
APPL_TRACE_LEVEL=0xFF
|
||||
PROTOCOL_TRACE_LEVEL=0xFFFFFFFF
|
||||
|
||||
###############################################################################
|
||||
# performance measurement
|
||||
# Change this setting to control how often USERIAL log the performance (throughput)
|
||||
# data on read/write/poll
|
||||
# defailt is to log performance dara for every 100 read or write
|
||||
#REPORT_PERFORMANCE_MEASURE=100
|
||||
|
||||
###############################################################################
|
||||
# File used for NFA storage
|
||||
NFA_STORAGE="/data/nfc"
|
||||
|
||||
###############################################################################
|
||||
# Snooze Mode Settings
|
||||
#
|
||||
# By default snooze mode is enabled. Set SNOOZE_MODE_CFG byte[0] to 0
|
||||
# to disable.
|
||||
#
|
||||
# If SNOOZE_MODE_CFG is not provided, the default settings are used:
|
||||
# They are as follows:
|
||||
# 8 Sleep Mode (0=Disabled 1=UART 8=SPI/I2C)
|
||||
# 0 Idle Threshold Host
|
||||
# 0 Idle Threshold HC
|
||||
# 0 NFC Wake active mode (0=ActiveLow 1=ActiveHigh)
|
||||
# 1 Host Wake active mode (0=ActiveLow 1=ActiveHigh)
|
||||
#
|
||||
#SNOOZE_MODE_CFG={08:00:00:00:01}
|
||||
|
||||
###############################################################################
|
||||
# Insert a delay in milliseconds after NFC_WAKE and before write to NFCC
|
||||
#NFC_WAKE_DELAY=20
|
||||
|
||||
###############################################################################
|
||||
# Various Delay settings (in ms) used in USERIAL
|
||||
# POWER_ON_DELAY
|
||||
# Delay after turning on chip, before writing to transport (default 300)
|
||||
# PRE_POWER_OFF_DELAY
|
||||
# Delay after deasserting NFC-Wake before turn off chip (default 0)
|
||||
# POST_POWER_OFF_DELAY
|
||||
# Delay after turning off chip, before USERIAL_close returns (default 0)
|
||||
#
|
||||
#POWER_ON_DELAY=300
|
||||
#PRE_POWER_OFF_DELAY=0
|
||||
#POST_POWER_OFF_DELAY=0
|
||||
|
||||
###############################################################################
|
||||
# Maximum time (ms) to wait for RESET NTF after setting REG_PU to high
|
||||
# The default is 1000.
|
||||
#NFCC_ENABLE_TIMEOUT=0
|
||||
|
||||
###############################################################################
|
||||
# LPTD mode configuration
|
||||
# byte[0] is the length of the remaining bytes in this value
|
||||
# if set to 0, LPTD params will NOT be sent to NFCC (i.e. disabled).
|
||||
# byte[1] is the param id it should be set to B9.
|
||||
# byte[2] is the length of the LPTD parameters
|
||||
# byte[3] indicates if LPTD is enabled
|
||||
# if set to 0, LPTD will be disabled (parameters will still be sent).
|
||||
# byte[4-n] are the LPTD parameters.
|
||||
# By default, LPTD is enabled and default settings are used.
|
||||
# See nfc_hal_dm_cfg.c for defaults
|
||||
#LPTD_CFG={23:B9:21:01:02:FF:FF:04:A0:0F:40:00:80:02:02:10:00:00:00:31:0C:30:00:00:00:00:00:00:00:00:00:00:00:00:00:00}
|
||||
|
||||
###############################################################################
|
||||
# Startup Configuration (100 bytes maximum)
|
||||
#
|
||||
# For the 0xCA parameter, byte[9] (marked by 'AA') is for UICC0, and byte[10] (marked by BB) is
|
||||
# for UICC1. The values are defined as:
|
||||
# 0 : UICCx only supports ISO_DEP in low power mode.
|
||||
# 2 : UICCx only supports Mifare in low power mode.
|
||||
# 3 : UICCx supports both ISO_DEP and Mifare in low power mode.
|
||||
#
|
||||
# AA BB
|
||||
#NFA_DM_START_UP_CFG={1F:CB:01:01:A5:01:01:CA:14:00:00:00:00:06:E8:03:00:00:00:00:00:00:00:00:00:00:00:00:00:80:01:01}
|
||||
|
||||
###############################################################################
|
||||
# Startup Vendor Specific Configuration (100 bytes maximum);
|
||||
# byte[0] TLV total len = 0x5
|
||||
# byte[1] NCI_MTS_CMD|NCI_GID_PROP = 0x2f
|
||||
# byte[2] NCI_MSG_FRAME_LOG = 0x9
|
||||
# byte[3] 2
|
||||
# byte[4] 0=turn off RF frame logging; 1=turn on
|
||||
# byte[5] 0=turn off SWP frame logging; 1=turn on
|
||||
# NFA_DM_START_UP_VSC_CFG={05:2F:09:02:01:01}
|
||||
|
||||
###############################################################################
|
||||
# Antenna Configuration - This data is used when setting 0xC8 config item
|
||||
# at startup (before discovery is started). If not used, no value is sent.
|
||||
#
|
||||
# The settings for this value are documented here:
|
||||
# http://wcgbu.broadcom.com/wpan/PM/Project%20Document%20Library/bcm20791B0/
|
||||
# Design/Doc/PHY%20register%20settings/BCM20791-B2-1027-02_PHY_Recommended_Reg_Settings.xlsx
|
||||
# This document is maintained by Paul Forshaw.
|
||||
#
|
||||
# The values marked as ?? should be tweaked per antenna or customer/app:
|
||||
# {20:C8:1E:06:??:00:??:??:??:00:??:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:??:01:00:00:40:04}
|
||||
# array[0] = 0x20 is length of the payload from array[1] to the end
|
||||
# array[1] = 0xC8 is PREINIT_DSP_CFG
|
||||
#PREINIT_DSP_CFG={20:C8:1E:06:1F:00:0F:03:3C:00:04:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:48:01:00:00:40:04}
|
||||
|
||||
###############################################################################
|
||||
# Configure crystal frequency when internal LPO can't detect the frequency.
|
||||
#XTAL_FREQUENCY=0
|
||||
###############################################################################
|
||||
# Configure the default Destination Gate used by HCI (the default is 4, which
|
||||
# is the ETSI loopback gate.
|
||||
NFA_HCI_DEFAULT_DEST_GATE=0xF0
|
||||
|
||||
###############################################################################
|
||||
# Configure the single default SE to use. The default is to use the first
|
||||
# SE that is detected by the stack. This value might be used when the phone
|
||||
# supports multiple SE (e.g. 0xF3 and 0xF4) but you want to force it to use
|
||||
# one of them (e.g. 0xF4).
|
||||
#ACTIVE_SE=0xF3
|
||||
|
||||
###############################################################################
|
||||
# Configure the default NfcA/IsoDep techology and protocol route. Can be
|
||||
# either a secure element (e.g. 0xF4) or the host (0x00)
|
||||
#DEFAULT_ISODEP_ROUTE=0x00
|
||||
|
||||
###############################################################################
|
||||
# Configure the NFC Extras to open and use a static pipe. If the value is
|
||||
# not set or set to 0, then the default is use a dynamic pipe based on a
|
||||
# destination gate (see NFA_HCI_DEFAULT_DEST_GATE). Note there is a value
|
||||
# for each UICC (where F3="UICC0" and F4="UICC1")
|
||||
#NFA_HCI_STATIC_PIPE_ID_F3=0x70
|
||||
#NFA_HCI_STATIC_PIPE_ID_01=0x19
|
||||
NFA_HCI_STATIC_PIPE_ID_C0=0x19
|
||||
NFA_HCI_STATIC_PIPE_ID_02=0x20
|
||||
###############################################################################
|
||||
# When disconnecting from Oberthur secure element, perform a warm-reset of
|
||||
# the secure element to deselect the applet.
|
||||
# The default hex value of the command is 0x3. If this variable is undefined,
|
||||
# then this feature is not used.
|
||||
#OBERTHUR_WARM_RESET_COMMAND=0x03
|
||||
|
||||
###############################################################################
|
||||
# Force UICC to only listen to the following technology(s).
|
||||
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
|
||||
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | NFA_TECHNOLOGY_MASK_F
|
||||
UICC_LISTEN_TECH_MASK=0x07
|
||||
|
||||
###############################################################################
|
||||
# Forcing HOST to listen for a selected protocol
|
||||
# 0x00 : Disable Host Listen
|
||||
# 0x01 : Enable Host to Listen (A) for ISO-DEP tech A
|
||||
# 0x02 : Enable Host to Listen (B) for ISO-DEP tech B
|
||||
# 0x04 : Enable Host to Listen (F) for T3T Tag Type Protocol tech F
|
||||
# 0x07 : Enable Host to Listen (ABF)for ISO-DEP tech AB & T3T Tag Type Protocol tech F
|
||||
HOST_LISTEN_TECH_MASK=0x07
|
||||
|
||||
###############################################################################
|
||||
# Enabling/Disabling Forward functionality
|
||||
# Disable 0x00
|
||||
# Enable 0x01
|
||||
NXP_FWD_FUNCTIONALITY_ENABLE=0x01
|
||||
|
||||
###############################################################################
|
||||
# Allow UICC to be powered off if there is no traffic.
|
||||
# Timeout is in ms. If set to 0, then UICC will not be powered off.
|
||||
#UICC_IDLE_TIMEOUT=30000
|
||||
UICC_IDLE_TIMEOUT=0
|
||||
|
||||
###############################################################################
|
||||
# AID for Empty Select command
|
||||
# If specified, this AID will be substituted when an Empty SELECT command is
|
||||
# detected. The first byte is the length of the AID. Maximum length is 16.
|
||||
AID_FOR_EMPTY_SELECT={08:A0:00:00:01:51:00:00:00}
|
||||
###############################################################################
|
||||
# Maximum Number of Credits to be allowed by the NFCC
|
||||
# This value overrides what the NFCC specifices allowing the host to have
|
||||
# the control to work-around transport limitations. If this value does
|
||||
# not exist or is set to 0, the NFCC will provide the number of credits.
|
||||
MAX_RF_DATA_CREDITS=1
|
||||
|
||||
###############################################################################
|
||||
# This setting allows you to disable registering the T4t Virtual SE that causes
|
||||
# the NFCC to send PPSE requests to the DH.
|
||||
# The default setting is enabled (i.e. T4t Virtual SE is registered).
|
||||
#REGISTER_VIRTUAL_SE=1
|
||||
|
||||
###############################################################################
|
||||
# When screen is turned off, specify the desired power state of the controller.
|
||||
# 0: power-off-sleep state; DEFAULT
|
||||
# 1: full-power state
|
||||
# 2: screen-off card-emulation (CE4/CE3/CE1 modes are used)
|
||||
SCREEN_OFF_POWER_STATE=1
|
||||
|
||||
###############################################################################
|
||||
# Firmware patch file
|
||||
# If the value is not set then patch download is disabled.
|
||||
#FW_PATCH="/vendor/firmware/bcm2079x_firmware.ncd"
|
||||
|
||||
###############################################################################
|
||||
# Firmware pre-patch file (sent before the above patch file)
|
||||
# If the value is not set then pre-patch is not used.
|
||||
#FW_PRE_PATCH="/vendor/firmware/bcm2079x_pre_firmware.ncd"
|
||||
|
||||
###############################################################################
|
||||
# Firmware patch format
|
||||
# 1 = HCD
|
||||
# 2 = NCD (default)
|
||||
#NFA_CONFIG_FORMAT=2
|
||||
|
||||
###############################################################################
|
||||
# SPD Debug mode
|
||||
# If set to 1, any failure of downloading a patch will trigger a hard-stop
|
||||
#SPD_DEBUG=0
|
||||
|
||||
###############################################################################
|
||||
# SPD Max Retry Count
|
||||
# The number of attempts to download a patch before giving up (defualt is 3).
|
||||
# Note, this resets after a power-cycle.
|
||||
#SPD_MAX_RETRY_COUNT=3
|
||||
|
||||
###############################################################################
|
||||
# transport driver
|
||||
#
|
||||
# TRANSPORT_DRIVER=<driver>
|
||||
#
|
||||
# where <driver> can be, for example:
|
||||
# "/dev/ttyS" (UART)
|
||||
# "/dev/bcmi2cnfc" (I2C)
|
||||
# "hwtun" (HW Tunnel)
|
||||
# "/dev/bcmspinfc" (SPI)
|
||||
# "/dev/btusb0" (BT USB)
|
||||
#TRANSPORT_DRIVER="/dev/bcm2079x-i2c"
|
||||
|
||||
###############################################################################
|
||||
# power control driver
|
||||
# Specify a kernel driver that support ioctl commands to control NFC_EN and
|
||||
# NFC_WAKE gpio signals.
|
||||
#
|
||||
# POWER_CONTRL_DRIVER=<driver>
|
||||
# where <driver> can be, for example:
|
||||
# "/dev/nfcpower"
|
||||
# "/dev/bcmi2cnfc" (I2C)
|
||||
# "/dev/bcmspinfc" (SPI)
|
||||
# i2c and spi driver may be used to control NFC_EN and NFC_WAKE signal
|
||||
#POWER_CONTROL_DRIVER="/dev/bcm2079x-i2c"
|
||||
|
||||
###############################################################################
|
||||
# I2C transport driver options
|
||||
# Mako does not support 10-bit I2C addresses
|
||||
# Revert to 7-bit address
|
||||
#BCMI2CNFC_ADDRESS=0x77
|
||||
|
||||
###############################################################################
|
||||
# I2C transport driver try to read multiple packets in read() if data is available
|
||||
# remove the comment below to enable this feature
|
||||
#READ_MULTIPLE_PACKETS=1
|
||||
|
||||
###############################################################################
|
||||
# SPI transport driver options
|
||||
#SPI_NEGOTIATION={0A:F0:00:01:00:00:00:FF:FF:00:00}
|
||||
|
||||
###############################################################################
|
||||
# UART transport driver options
|
||||
#
|
||||
# PORT=1,2,3,...
|
||||
# BAUD=115200, 19200, 9600, 4800,
|
||||
# DATABITS=8, 7, 6, 5
|
||||
# PARITY="even" | "odd" | "none"
|
||||
# STOPBITS="0" | "1" | "1.5" | "2"
|
||||
|
||||
#UART_PORT=2
|
||||
#UART_BAUD=115200
|
||||
#UART_DATABITS=8
|
||||
#UART_PARITY="none"
|
||||
#UART_STOPBITS="1"
|
||||
|
||||
###############################################################################
|
||||
# Insert a delay in microseconds per byte after a write to NFCC.
|
||||
# after writing a block of data to the NFCC, delay this an amopunt of time before
|
||||
# writing next block of data. the delay is calculated as below
|
||||
# NFC_WRITE_DELAY * (number of byte written) / 1000 milliseconds
|
||||
# e.g. after 259 bytes is written, delay (259 * 20 / 1000) 5 ms before next write
|
||||
#NFC_WRITE_DELAY=20
|
||||
|
||||
###############################################################################
|
||||
# Maximum Number of Credits to be allowed by the NFCC
|
||||
# This value overrides what the NFCC specifices allowing the host to have
|
||||
# the control to work-around transport limitations. If this value does
|
||||
# not exist or is set to 0, the NFCC will provide the number of credits.
|
||||
MAX_RF_DATA_CREDITS=1
|
||||
|
||||
###############################################################################
|
||||
# Default poll duration (in ms)
|
||||
# The defualt is 500ms if not set (see nfc_target.h)
|
||||
#NFA_DM_DISC_DURATION_POLL=333
|
||||
###############################################################################
|
||||
# Antenna Configuration - This data is used when setting 0xC8 config item
|
||||
# at startup (before discovery is started). If not used, no value is sent.
|
||||
#
|
||||
# The settings for this value are documented here:
|
||||
# http://wcgbu.broadcom.com/wpan/PM/Project%20Document%20Library/bcm20791B0/
|
||||
# Design/Doc/PHY%20register%20settings/BCM20791-B2-1027-02_PHY_Recommended_Reg_Settings.xlsx
|
||||
# This document is maintained by Paul Forshaw.
|
||||
#
|
||||
# The values marked as ?? should be tweaked per antenna or customer/app:
|
||||
# {20:C8:1E:06:??:00:??:??:??:00:??:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:??:01:00:00:40:04}
|
||||
# array[0] = 0x20 is length of the payload from array[1] to the end
|
||||
# array[1] = 0xC8 is PREINIT_DSP_CFG
|
||||
#PREINIT_DSP_CFG={20:C8:1E:06:1F:00:0F:03:3C:00:04:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:48:01:00:00:40:04}
|
||||
|
||||
|
||||
###############################################################################
|
||||
# Choose the presence-check algorithm for type-4 tag. If not defined, the default value is 1.
|
||||
# 0 NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm
|
||||
# 1 NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block
|
||||
# 2 NFA_RW_PRES_CHK_RESET; Deactivate to Sleep, then re-activate
|
||||
# 3 NFA_RW_PRES_CHK_RB_CH0; Type-4 tag protocol's ReadBinary command on channel 0
|
||||
# 4 NFA_RW_PRES_CHK_RB_CH3; Type-4 tag protocol's ReadBinary command on channel 3
|
||||
PRESENCE_CHECK_ALGORITHM=1
|
||||
|
||||
###############################################################################
|
||||
# Force tag polling for the following technology(s).
|
||||
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
|
||||
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B |
|
||||
# NFA_TECHNOLOGY_MASK_F | NFA_TECHNOLOGY_MASK_ISO15693 |
|
||||
# NFA_TECHNOLOGY_MASK_B_PRIME | NFA_TECHNOLOGY_MASK_KOVIO |
|
||||
# NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE.
|
||||
#
|
||||
# Notable bits:
|
||||
# NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A */
|
||||
# NFA_TECHNOLOGY_MASK_B 0x02 /* NFC Technology B */
|
||||
# NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F */
|
||||
# NFA_TECHNOLOGY_MASK_ISO15693 0x08 /* Proprietary Technology */
|
||||
# NFA_TECHNOLOGY_MASK_KOVIO 0x20 /* Proprietary Technology */
|
||||
# NFA_TECHNOLOGY_MASK_A_ACTIVE 0x40 /* NFC Technology A active mode */
|
||||
# NFA_TECHNOLOGY_MASK_F_ACTIVE 0x80 /* NFC Technology F active mode */
|
||||
POLLING_TECH_MASK=0xEF
|
||||
|
||||
###############################################################################
|
||||
# Force P2P to only listen for the following technology(s).
|
||||
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
|
||||
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_F |
|
||||
# NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE
|
||||
#
|
||||
# Notable bits:
|
||||
# NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A */
|
||||
# NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F */
|
||||
# NFA_TECHNOLOGY_MASK_A_ACTIVE 0x40 /* NFC Technology A active mode */
|
||||
# NFA_TECHNOLOGY_MASK_F_ACTIVE 0x80 /* NFC Technology F active mode */
|
||||
P2P_LISTEN_TECH_MASK=0xC5
|
||||
|
||||
PRESERVE_STORAGE=0x01
|
||||
|
||||
###############################################################################
|
||||
# NCI Hal Module name
|
||||
NCI_HAL_MODULE="nfc_nci"
|
||||
|
||||
##############################################################################
|
||||
# Deactivate notification wait time out in seconds used in ETSI Reader mode
|
||||
# 0 - Infinite wait
|
||||
NFA_DM_DISC_NTF_TIMEOUT=100
|
||||
|
||||
###############################################################################
|
||||
# AID_MATCHING constants
|
||||
# AID_MATCHING_EXACT_ONLY 0x00
|
||||
# AID_MATCHING_EXACT_OR_PREFIX 0x01
|
||||
# AID_MATCHING_PREFIX_ONLY 0x02
|
||||
AID_MATCHING_MODE=0x01
|
||||
|
||||
###############################################################################
|
||||
# Default Secure Element route id
|
||||
DEFAULT_OFFHOST_ROUTE=0x02
|
||||
|
||||
###############################################################################
|
||||
# Vendor Specific Proprietary Protocol & Discovery Configuration
|
||||
# Set to 0xFF if unsupported
|
||||
# byte[0] NCI_PROTOCOL_18092_ACTIVE
|
||||
# byte[1] NCI_PROTOCOL_B_PRIME
|
||||
# byte[2] NCI_PROTOCOL_DUAL
|
||||
# byte[3] NCI_PROTOCOL_15693
|
||||
# byte[4] NCI_PROTOCOL_KOVIO
|
||||
# byte[5] NCI_PROTOCOL_MIFARE
|
||||
# byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO
|
||||
# byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME
|
||||
# byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME
|
||||
NFA_PROPRIETARY_CFG={05:FF:FF:06:81:80:70:FF:FF}
|
||||
|
||||
#################################################################################
|
||||
# Bail out mode
|
||||
# If set to 1, NFCC is using bail out mode for either Type A or Type B poll.
|
||||
NFA_POLL_BAIL_OUT_MODE=0x01
|
||||
############################################################################## #
|
||||
#White list of Hosts
|
||||
#This values will be the Hosts(NFCEEs) in the HCI Network.
|
||||
DEVICE_HOST_WHITE_LIST={80 : 81 : C0}
|
||||
110
nfc/libnfc-nci.conf
Normal file
110
nfc/libnfc-nci.conf
Normal file
@@ -0,0 +1,110 @@
|
||||
###################### Start of libnfc-nci.conf #######################
|
||||
|
||||
###############################################################################
|
||||
# Application options
|
||||
APPL_TRACE_LEVEL=0xFF
|
||||
PROTOCOL_TRACE_LEVEL=0xFFFFFFFF
|
||||
|
||||
###############################################################################
|
||||
# File used for NFA storage
|
||||
NFA_STORAGE="/data/nfc"
|
||||
|
||||
###############################################################################
|
||||
# Force UICC to only listen to the following technology(s).
|
||||
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
|
||||
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | NFA_TECHNOLOGY_MASK_F
|
||||
UICC_LISTEN_TECH_MASK=0x07
|
||||
|
||||
###############################################################################
|
||||
# Configure the default Destination Gate used by HCI (the default is 4, which
|
||||
# is the ETSI loopback gate.
|
||||
NFA_HCI_DEFAULT_DEST_GATE=0xF0
|
||||
|
||||
###############################################################################
|
||||
# Forcing HOST to listen for a selected protocol
|
||||
# 0x00 : Disable Host Listen
|
||||
# 0x01 : Enable Host to Listen (A) for ISO-DEP tech A
|
||||
# 0x02 : Enable Host to Listen (B) for ISO-DEP tech B
|
||||
# 0x04 : Enable Host to Listen (F) for T3T Tag Type Protocol tech F
|
||||
# 0x07 : Enable Host to Listen (ABF)for ISO-DEP tech AB & T3T Tag Type Protocol tech F
|
||||
HOST_LISTEN_TECH_MASK=0x07
|
||||
|
||||
###############################################################################
|
||||
# Enabling/Disabling Forward functionality
|
||||
# Disable 0x00
|
||||
# Enable 0x01
|
||||
NXP_FWD_FUNCTIONALITY_ENABLE=0x01
|
||||
|
||||
###############################################################################
|
||||
# AID for Empty Select command
|
||||
# If specified, this AID will be substituted when an Empty SELECT command is
|
||||
# detected. The first byte is the length of the AID. Maximum length is 16.
|
||||
AID_FOR_EMPTY_SELECT={08:A0:00:00:01:51:00:00:00}
|
||||
|
||||
###############################################################################
|
||||
# When screen is turned off, specify the desired power state of the controller.
|
||||
# 0: power-off-sleep state; DEFAULT
|
||||
# 1: full-power state
|
||||
# 2: screen-off card-emulation (CE4/CE3/CE1 modes are used)
|
||||
SCREEN_OFF_POWER_STATE=1
|
||||
|
||||
###############################################################################
|
||||
# Firmware patch format, Only 1 and 5 should be set
|
||||
# 0 -> NFC Default
|
||||
# 1 -> EMVCO Default
|
||||
# 3 -> EMVCO Polling, DISC_IDLE = POWER_OFF, DISC DEACTIVATE = Removal process
|
||||
# 5 -> EMVCO Cert Polling, DISC_IDLE = Removal process , DISC DEACTIVATE = POWER_OFF
|
||||
# 7 -> EMVCO Polling, DISC_IDLE = POWER_OFF, DISC DEACTIVATE = POWER_OFF
|
||||
NFA_CONFIG_FORMAT=1
|
||||
|
||||
###############################################################################
|
||||
# Default poll duration (in ms)
|
||||
# The defualt is 500ms if not set (see nfc_target.h)
|
||||
#NFA_DM_DISC_DURATION_POLL=333
|
||||
|
||||
###############################################################################
|
||||
# Force tag polling for the following technology(s).
|
||||
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
|
||||
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B |
|
||||
# NFA_TECHNOLOGY_MASK_F | NFA_TECHNOLOGY_MASK_ISO15693 |
|
||||
# NFA_TECHNOLOGY_MASK_B_PRIME | NFA_TECHNOLOGY_MASK_KOVIO |
|
||||
# NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE.
|
||||
#
|
||||
# Notable bits:
|
||||
# NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A */
|
||||
# NFA_TECHNOLOGY_MASK_B 0x02 /* NFC Technology B */
|
||||
# NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F */
|
||||
# NFA_TECHNOLOGY_MASK_ISO15693 0x08 /* Proprietary Technology */
|
||||
# NFA_TECHNOLOGY_MASK_KOVIO 0x20 /* Proprietary Technology */
|
||||
# NFA_TECHNOLOGY_MASK_A_ACTIVE 0x40 /* NFC Technology A active mode */
|
||||
# NFA_TECHNOLOGY_MASK_F_ACTIVE 0x80 /* NFC Technology F active mode */
|
||||
POLLING_TECH_MASK=0xEF
|
||||
|
||||
###############################################################################
|
||||
# Force P2P to only listen for the following technology(s).
|
||||
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
|
||||
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_F |
|
||||
# NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE
|
||||
#
|
||||
# Notable bits:
|
||||
# NFA_TECHNOLOGY_MASK_A 0x01 /* NFC Technology A */
|
||||
# NFA_TECHNOLOGY_MASK_F 0x04 /* NFC Technology F */
|
||||
# NFA_TECHNOLOGY_MASK_A_ACTIVE 0x40 /* NFC Technology A active mode */
|
||||
# NFA_TECHNOLOGY_MASK_F_ACTIVE 0x80 /* NFC Technology F active mode */
|
||||
P2P_LISTEN_TECH_MASK=0xC5
|
||||
|
||||
PRESERVE_STORAGE=0x01
|
||||
|
||||
##############################################################################
|
||||
# Deactivate notification wait time out in seconds used in ETSI Reader mode
|
||||
# 0 - Infinite wait
|
||||
NFA_DM_DISC_NTF_TIMEOUT=0
|
||||
|
||||
###############################################################################
|
||||
# AID_MATCHING constants
|
||||
# AID_MATCHING_EXACT_ONLY 0x00
|
||||
# AID_MATCHING_EXACT_OR_PREFIX 0x01
|
||||
# AID_MATCHING_PREFIX_ONLY 0x02
|
||||
AID_MATCHING_MODE=0x01
|
||||
|
||||
###############################################################################
|
||||
@@ -67,8 +67,9 @@ NXP_SYS_CLK_SRC_SEL=0x01
|
||||
#define CLK_FREQ_19_2MHZ 2
|
||||
#define CLK_FREQ_24MHZ 3
|
||||
#define CLK_FREQ_26MHZ 4
|
||||
#define CLK_FREQ_38_4MHZ 5
|
||||
#define CLK_FREQ_52MHZ 6
|
||||
#define CLK_FREQ_32MHZ 5
|
||||
#define CLK_FREQ_38_4MHZ 6
|
||||
#define CLK_FREQ_52MHZ 7
|
||||
NXP_SYS_CLK_FREQ_SEL=0x01
|
||||
|
||||
###############################################################################
|
||||
@@ -255,9 +256,20 @@ NXP_CORE_CONF={ 20, 02, 2E, 0E,
|
||||
# No secure element 0x00
|
||||
# eSE 0x01
|
||||
# UICC 0x02
|
||||
# UICC2 0x04
|
||||
NXP_DEFAULT_SE=0x01
|
||||
|
||||
###############################################################################
|
||||
# Force ESE to only listen to the following technology(s).
|
||||
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
|
||||
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B | NFA_TECHNOLOGY_MASK_F
|
||||
NXP_ESE_LISTEN_TECH_MASK=0x07
|
||||
|
||||
###############################################################################
|
||||
#set autonomous mode
|
||||
# disable autonomous 0x00
|
||||
# enable autonomous 0x01
|
||||
NXP_CORE_SCRN_OFF_AUTONOMOUS_ENABLE=0x00
|
||||
|
||||
###############################################################################
|
||||
# Enable SWP full power mode when phone is power off
|
||||
NXP_SWP_FULL_PWR_ON=0x00
|
||||
@@ -289,46 +301,50 @@ NXP_DEFAULT_NFCEE_TIMEOUT=0x06
|
||||
|
||||
###############################################################################
|
||||
# Timeout in secs
|
||||
NXP_SWP_RD_START_TIMEOUT=0x0A
|
||||
|
||||
# Timeout in secs
|
||||
NXP_SWP_RD_TAG_OP_TIMEOUT=0x01
|
||||
NXP_SWP_RD_TAG_OP_TIMEOUT=0x20
|
||||
|
||||
###############################################################################
|
||||
|
||||
# Set the default AID route Location :
|
||||
# This settings will be used when application does not set this parameter
|
||||
# host 0x00
|
||||
# eSE 0x01
|
||||
# UICC 0x02
|
||||
# UICC2 0x04
|
||||
DEFAULT_AID_ROUTE=0x01
|
||||
|
||||
###############################################################################
|
||||
# Set the Mifare Desfire route Location :
|
||||
# This settings will be used when application does not set this parameter
|
||||
# Configure the default NfcA/IsoDep techology and protocol route. Can be
|
||||
# either a secure element (e.g. 0xF4) or the host (0x00)
|
||||
# host 0x00
|
||||
# eSE 0x01
|
||||
# UICC 0x02
|
||||
# UICC2 0x04
|
||||
DEFAULT_DESFIRE_ROUTE=0x01
|
||||
DEFAULT_ROUTE=0x00
|
||||
|
||||
###############################################################################
|
||||
# Set the Mifare CLT route Location :
|
||||
# This settings will be used when application does not set this parameter
|
||||
# Configure the single default SE to use. The default is to use the first
|
||||
# SE that is detected by the stack. This value might be used when the phone
|
||||
# supports multiple SE (e.g. 0xC0 and 0x80) but you want to force it to use
|
||||
# one of them (e.g. 0xC0).
|
||||
# host 0x00
|
||||
# eSE 0x01
|
||||
# UICC 0x02
|
||||
# UICC2 0x04
|
||||
DEFAULT_MIFARE_CLT_ROUTE=0x01
|
||||
DEFAULT_OFFHOST_ROUTE=0x01
|
||||
|
||||
###############################################################################
|
||||
# Set the Felica CLT route Location :
|
||||
# This settings will be used when application does not set this parameter
|
||||
# Configure the single default SE to use. The default is to use the first
|
||||
# SE that is detected by the stack. This value might be used when the phone
|
||||
# supports multiple SE (e.g. 0xF3 and 0xF4) but you want to force it to use
|
||||
# one of them (e.g. 0xF4).
|
||||
# host 0x00
|
||||
# eSE 0x01
|
||||
# UICC 0x02
|
||||
# UICC2 0x04
|
||||
DEFAULT_FELICA_CLT_ROUTE=0x01
|
||||
DEFAULT_NFCF_ROUTE=0x01
|
||||
|
||||
###############################################################################
|
||||
#Set the default Felica T3T System Code OffHost route Location :
|
||||
#This settings will be used when application does not set this parameter
|
||||
# host 0x00
|
||||
# eSE 0xC0
|
||||
DEFAULT_SYS_CODE_ROUTE=0xC0
|
||||
|
||||
###############################################################################
|
||||
# Set the default AID Power state :
|
||||
@@ -348,7 +364,7 @@ DEFAULT_AID_PWR_STATE=0x19
|
||||
# bit pos 2 = Battery Off
|
||||
# bit pos 3 = Screen Lock
|
||||
# bit pos 4 = Screen Off
|
||||
DEFAULT_DESFIRE_PWR_STATE=0x1B
|
||||
DEFAULT_ROUTE_PWR_STATE=0x1B
|
||||
|
||||
###############################################################################
|
||||
# Set the Mifare CLT Power state :
|
||||
@@ -358,7 +374,7 @@ DEFAULT_DESFIRE_PWR_STATE=0x1B
|
||||
# bit pos 2 = Battery Off
|
||||
# bit pos 3 = Screen Lock
|
||||
# bit pos 4 = Screen Off
|
||||
DEFAULT_MIFARE_CLT_PWR_STATE=0x1B
|
||||
DEFAULT_OFFHOST_PWR_STATE=0x1B
|
||||
|
||||
###############################################################################
|
||||
# Set the Felica CLT Power state :
|
||||
@@ -370,6 +386,29 @@ DEFAULT_MIFARE_CLT_PWR_STATE=0x1B
|
||||
# bit pos 4 = Screen Off
|
||||
DEFAULT_FELICA_CLT_PWR_STATE=0x1B
|
||||
|
||||
###############################################################################
|
||||
#Set the SYS_CODE Power state :
|
||||
#This settings will be used when application does not set this parameter
|
||||
# bit pos 0 = Switch On
|
||||
# bit pos 1 = Switch Off
|
||||
# bit pos 2 = Battery Off
|
||||
# bit pos 3 = Screen Lock
|
||||
# bit pos 4 = Screen Off
|
||||
DEFAULT_SYS_CODE_PWR_STATE=0x1B
|
||||
|
||||
###############################################################################
|
||||
# Configure the NFC Extras to open and use a static pipe. If the value is
|
||||
# not set or set to 0, then the default is use a dynamic pipe based on a
|
||||
# destination gate (see NFA_HCI_DEFAULT_DEST_GATE). Note there is a value
|
||||
# for each UICC (where F3="UICC0" and F4="UICC1")
|
||||
OFF_HOST_ESE_PIPE_ID=0x19
|
||||
OFF_HOST_SIM_PIPE_ID=0x0A
|
||||
|
||||
###############################################################################
|
||||
# Bail out mode
|
||||
# If set to 1, NFCC is using bail out mode for either Type A or Type B poll.
|
||||
NFA_POLL_BAIL_OUT_MODE=0x01
|
||||
|
||||
###############################################################################
|
||||
# AID Matching platform options
|
||||
# AID_MATCHING_L 0x01
|
||||
@@ -456,12 +495,6 @@ NXP_UICC_WIRED_PRT_MASK=0x00
|
||||
# allow wired mode = 0
|
||||
NXP_WIRED_MODE_RF_FIELD_ENABLE=0x00
|
||||
|
||||
###############################################################################
|
||||
# UICC mode supported
|
||||
# Disable 0x00
|
||||
# Enable 0x01
|
||||
NXP_DUAL_UICC_ENABLE=0x00
|
||||
|
||||
###############################################################################
|
||||
# Config to allow adding aids
|
||||
# NFC on/off is required after this config
|
||||
@@ -480,6 +513,20 @@ NXP_CP_TIMEOUT={00, 77}
|
||||
# Enable 0x01
|
||||
NXP_CHECK_DEFAULT_PROTO_SE_ID=0x01
|
||||
|
||||
###############################################################################
|
||||
# SVDD sync off Delay in ms it can be max 20 ms
|
||||
# If out of range timeout used, default delay of 10ms will be set
|
||||
NXP_SVDD_SYNC_OFF_DELAY=10
|
||||
|
||||
###############################################################################
|
||||
#NXP_CN_TRANSIT_CMA_BYPASSMODE_ENABLE
|
||||
#Enable this config it prevents EMVCo PICC compliancy and Mifare backward compatibility works
|
||||
#Disable this config EMVCo PICC compliancy works and Mifare backward compatibility will not work
|
||||
#Default config is Disable
|
||||
#Enable 0x01
|
||||
#Disable 0x00
|
||||
NXP_CN_TRANSIT_CMA_BYPASSMODE_ENABLE=0x00
|
||||
|
||||
###############################################################################
|
||||
# NXP_CN_TRANSIT_BLK_NUM_CHECK_ENABLE
|
||||
# Enable/Disable block number checks for china transit use case
|
||||
@@ -487,6 +534,24 @@ NXP_CHECK_DEFAULT_PROTO_SE_ID=0x01
|
||||
# Disable 0x00
|
||||
NXP_CN_TRANSIT_BLK_NUM_CHECK_ENABLE=0x01
|
||||
|
||||
###############################################################################
|
||||
#Enable NXP NCI runtime parser library
|
||||
#Enable 0x01
|
||||
#Disable 0x00
|
||||
NXP_NCI_PARSER_LIBRARY=0x00
|
||||
|
||||
###############################################################################
|
||||
#This config will enable different level of Rf transaction debugs based on the
|
||||
#following values provided. Decoded information will be printed in adb logcat
|
||||
#Debug Mode Levels
|
||||
#Disable Debug 0x00
|
||||
#L1 Debug 0x01
|
||||
#L2 Debug 0x02
|
||||
#L1 & L2 Debug 0x03
|
||||
#L1 & L2 & RSSI 0x04
|
||||
#L1 & L2 & Felica 0x05
|
||||
#NXP_CORE_PROP_SYSTEM_DEBUG=0x00
|
||||
|
||||
###############################################################################
|
||||
# Wired mode resume timeout vaule in wired mode resume feature enable
|
||||
NXP_WIREDMODE_RESUME_TIMEOUT = 0x02
|
||||
@@ -503,14 +568,81 @@ NXP_ESE_POWER_DH_CONTROL=1
|
||||
# External PMU available only in phone ON case if NXP_ESE_POWER_EXT_PMU=2
|
||||
NXP_ESE_POWER_EXT_PMU=2
|
||||
|
||||
###############################################################################
|
||||
# Enable/Disable mifare desfire CE prio feature
|
||||
# Disable 0x00
|
||||
# Enable 0x01
|
||||
NXP_MIFARE_DESFIRE_DISABLE=0x00
|
||||
|
||||
###############################################################################
|
||||
# Whether to allow wired mode in desfire and mifare CLT
|
||||
# Disable 0x00
|
||||
# Enable 0x01
|
||||
NXP_ALLOW_WIRED_IN_MIFARE_DESFIRE_CLT=0x00
|
||||
|
||||
###############################################################################
|
||||
# Enable/Disable Block Route feature.
|
||||
# Block Route will restrict routing to first matched rule
|
||||
# Block Route enable 0x01
|
||||
# Block Route disable 0x00
|
||||
AID_BLOCK_ROUTE=0x00
|
||||
|
||||
###############################################################################
|
||||
# Send DWP interface reset command as part of SE open
|
||||
# Disable 0x00
|
||||
# Enable 0x01
|
||||
NXP_DWP_INTF_RESET_ENABLE=0x00
|
||||
|
||||
###############################################################################
|
||||
# Timeout value in milliseconds for JCOP OS download to complete
|
||||
OS_DOWNLOAD_TIMEOUT_VALUE=60000
|
||||
|
||||
###############################################################################
|
||||
# Timeout value in milliseconds to send response for Felica command received
|
||||
NXP_HCEF_CMD_RSP_TIMEOUT_VALUE=5000
|
||||
|
||||
###############################################################################
|
||||
# Maximum WTX requests entertained by MW
|
||||
NXP_WM_MAX_WTX_COUNT=50
|
||||
|
||||
###############################################################################
|
||||
# HAL library path for selftest
|
||||
NXP_HAL_PATH="/vendor/lib64/hw/nfc_nci.pn54x.so"
|
||||
|
||||
###############################################################################
|
||||
# Enable or Disable RF_STATUS_UPDATE to EseHal module
|
||||
# Disable 0x00
|
||||
# Enable 0x01
|
||||
RF_STATUS_UPDATE_ENABLE=0x00
|
||||
|
||||
###############################################################################
|
||||
# Vendor Specific Proprietary Protocol & Discovery Configuration
|
||||
# Set to 0xFF if unsupported
|
||||
# byte[0] NCI_PROTOCOL_18092_ACTIVE
|
||||
# byte[1] NCI_PROTOCOL_B_PRIME
|
||||
# byte[2] NCI_PROTOCOL_DUAL
|
||||
# byte[3] NCI_PROTOCOL_15693
|
||||
# byte[4] NCI_PROTOCOL_KOVIO
|
||||
# byte[5] NCI_PROTOCOL_MIFARE
|
||||
# byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO
|
||||
# byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME
|
||||
# byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME
|
||||
NFA_PROPRIETARY_CFG={05, FF, FF, 06, 81, 80, 70, FF, FF}
|
||||
|
||||
###############################################################################
|
||||
#White list of Hosts
|
||||
#This values will be the Hosts(NFCEEs) in the HCI Network.
|
||||
DEVICE_HOST_WHITE_LIST={C0, 02}
|
||||
|
||||
###############################################################################
|
||||
# Choose the presence-check algorithm for type-4 tag. If not defined, the default value is 1.
|
||||
# 0 NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm
|
||||
# 1 NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block
|
||||
# 2 NFA_RW_PRES_CHK_ISO_DEP_NAK; Type - 4 tag protocol iso-dep nak presence check
|
||||
PRESENCE_CHECK_ALGORITHM=2
|
||||
|
||||
###############################################################################
|
||||
# Extended APDU length for ISO_DEP
|
||||
ISO_DEP_MAX_TRANSCEIVE=0xFEFF
|
||||
|
||||
###############################################################################
|
||||
# Disable Mifare CLT for JCOP4.1
|
||||
# Enable 0x01
|
||||
# Disable 0x00
|
||||
#NXP_MF_CLT_JCOP_CFG=0x01
|
||||
|
||||
###############################################################################
|
||||
|
||||
Reference in New Issue
Block a user