Some firmware images support the processing of SMC calls via the
waitqueue mechanism. Add compatible string to support this feature.
Change-Id: I8bc4d4ea41c247c93683e9d0dc2e9a47de063bef
Add doorbell test node to kalama.dtsi and kalama-vm.dtsi to
validate hypervisor doorbell functionality.
Change-Id: I4b13064644f66f30915b7692efaf5bc23978155d
Add "qcom,wf-fifo-preload" property for FIFO effects to be able to
preload into pattern memory during boot up.
Change-Id: Icb11c5efc7039abe290d024288d964c651b21d4e
Update the Qualcomm Technologies, INC. PMIC GPIO binding documentation
to include compatible strings for the Kalama PMICS.
Kalama PMICS include PM8550, PM8550B, PM8550VE, PM8550VS, PMK8550
and PMR735D.
Change-Id: I604c478a8ec8afe79f4460a05f2c444048926cd9
Remove documentation for the qcom,deferred-regulator-disable-delay
property, as it is no longer supported.
Change-Id: Ie0beaaf082beb7d421a68b6dca3fbb66094136a7
Add documentation for device-tree bindings for EP-PCIe
driver used in msm platforms, ported from 5.4.c3.
Change-Id: I4ac9fc2fc789774b225e46df54a28465cc2b2ab9
Update bindings to mention multiple DRVs in a single RSC device.
Also update to mention SW or HW channel use and examples.
Change-Id: I75658d2383626238bcb326f8959867cefc61f9bf
Add ADSP sleep monitor document to add details
about ADSP sleep monitor and device tree properties.
Change-Id: Iceeb5d08f6d83e0eaa658211af4516f4c3957553
Since drv processor subsystem can be supported on CDSP
or LPASS based on the target, pass the name of the DRV
from device tree. Use the presence of this property as
indication of DRV support as well. New property name is
qcom,drv-name.
Change-Id: I4d03bfdd430a3eea428a6f6aee067d76d6731829
Adding pinctrl bindings to support vm on Kalama.
This is snapshot of bindings from 'commit 53311cb5fada
("Merge "ARM: dts: msm: Remove Waipio GenC GPU strings"")'
from device tree project msm-5.10 branch.
Change-Id: Ifa51cd9cab904d52fadef418881d79d78d1c07b1
Add bindings for SW-calibrated ADC used on PMR735A/PMR735B on
targets which don't have PMK8350 running in master mode.
Change-Id: I753b3caf1e52ac9920a9df32cbef465277409700
PMIC5 GEN3 ADC has support for clients to read voltage and
current on supported channels connected to the PMIC.
Clients include reading voltage phone power and on board system
thermistors for thermal management. ADCs on certain PMICs have
support to read battery current.
Change-Id: Ief7cbdf77d227ba2cb4ef7919aa66d9962d98e37
Add documentation describing the devicetree properties for the Cinder
TLMM block as a pinctrl device.
Change-Id: Ia78ee5ef0fae13b63b51c73315330484bdef1f92
Add shutdown voltage which if specified can initiate a shutdown
when battery voltage goes below that threshold, battery SOC is
0 and device is not charging.
Change-Id: I592e6abe39ec76c64bf87e9e2aeac9b59cd6a7f6
Add "qcom,thermal-mitigation" property to configure fast charging
current for different system thermal mitigation levels.
Change-Id: Ia07b24d85d904e6e623ba547973f5a5779305784
Add DT bindings for QTI battery charger which gets and sets
power supply properties by communicating with charger firmware
running on the remote subsystem (e.g. DSP) over PMIC Glink.
Change-Id: I8e3aedfb70c627807388db3c449c283f35ecfd59
Document the qcom,pmic-fault-panic property which is used to
indicate that the device should trigger a controlled panic
shutdown if the preceding restart was caused by a PMIC fault.
Change-Id: I8f26730cfd7419bd8fac126bd40bf537b8be1ce2
Add a definition for the qcom,bus-id property which is used on
PMIC arbiter 7 to specify which SPMI bus interface to use (i.e.
the primary or secondary one).
Change-Id: I8249e43b34a980567e9073a2c2756532b0f1f258
